Electric Actuator High Rigidity and High Precision Slider Type Circular arc grooves allow for high rigidity and high precision. Moment resistance*1 *2 61% Improved by up to Table displacement*1 50% Reduced by up to With internal battery-less absolute e As a result, it is necessary for the customer to verify compliance with the EMC directive for the machinery and equipment as a whole. The actuator and controller are sold as a package. Confirm that the combination of the controller and actuator is correct.
17.5 5.5 2.5 33 20 42 8 5 28 M4 x 0.7 M10 x 1.0 12.5 9.5 46 74 16 15 18 18 20 20 5 8 19 5.5 2.5 33 20 42 8 5 28 M5 x 0.8 M12 x 1.0 12.5 9.5 47 75 R V Double clevis type (D)/CJ5DS CDH9 +0.030 0 Cdd9 0.030 0.060 NB GA GB Piping port 2-M5 x 0.8 Clevis pin ( ) MM CA CB D NA A CX + 0.2 + 0.1 U BA S + Stroke Z + Stroke ZZ + Stroke BB H R (mm) CD (Cd) A BA BB CA CB CX D GA GB H MM NA NB R S U Z
Applicable to a wide range of applications. Pleated type has 3 times the filtration area of a cylinder. Filters are economical because they can be cleaned and repeatedly used. Main applications Please use 40 microns or less as a highprecision filter, and 74 microns or higher as a high-grade strainer. All types of gases and fluids, high-temperature fluids.
Contact SMC if a stopper cylinder is to be used for stopping a load that is connected directly to a cylinder, as this will cause the cylinder's thrust to act as a horizontal load.
vacuum holding application such as a leak tester, since there is leakage.
(Mainly when using an external guide) When using it as a load balancer, please contact SMC sales representatives. Load mass (kg) m1 MY1B MY1B MY1H 3. Consider uncalculated loads such as piping, cableveyor, etc., when selecting a load moment Calculation does not include the external acting force of piping, cableveyor, etc.
Type Series VQ5000 Dimensions (mm) 1in 25.4mm Bottom port diagram With connector on U side (FU) 106 46.8 59.2 83.5 9 9 55.5 M5 ground screw 2n-1/2 (ports A, B) 34.5 n U side X 12 B 2 A 4 6 B A B 2 A 4 5 SMC SMC SMC SMC SMC B A B 2 A 4 4 B A P=41 L1 L2 B 2 A 4 3 B A B 2 A 4 2 B A 34.5 46 68.5 P = 41 B 2 A 4 1 B A 58.5 X 12 Stations 2-1/8 (external pilot port) 15.5 22 51 69 117 42 16 107.8
When the cylinder is mounted on the housing, and the plates are used for high-speed operation or used as a pusher, use a connector plate to bridge both plates. Failure to do so could cause the snap ring to become detached or the set screws to shift, causing the plates to fall off.
Moment (Nm) Payload (N) ML1C/M2,M3 How to calculate the load ratio A. Consider q Max. payload, w static moment, e dynamic moment (when stopper collides) when calculating the Max. allowable moment and payload. Evaluate q and w as a (average speed), and e as (collision speed =1.4a).
+ Stroke B + Stroke Dimensions GB 40 63 100 A B Bore size (mm) 36.5 58 48.5 GB 38 73 61.5 38 78 66.5 Dimensions other than the above are the same as standard products.
power cut or forcible de-energizing The setting of the product will be retained as it was before a power cut or de-energizing.
The length of the lead wires between the switch unit and contact protection box should be no more than 1m, and they should be placed as close together as possible. Tighten with a torque of 0.10 to 0.20Nm. As a rule, it should be turned about 90 past the point at which tightening can be felt.
C.O. style easy to use; operatable as either N.C. or N.O. Easy to disassemble and reassemble in a short time. Compatible with high viscosity fluids (500cSt). VX VNl VQ Variations ValveO OPilot port (Free take off direction) 1 8 Connecting port size Pilot pressure Rc(PT) 0.25 to 0.7 (MPa) A Common (C.O.)
(Same side) A HS Number of switches 20 25 32 40 50 63 80 100 31.5 26 24 Mounting surface Port surface Port surface Port surface 31.5 28.5 24 32.5 33 25 37 36.5 28 45.5 42 36 45.5 48.5 36 Switch type 56 57.5 46 Minimum stroke (mm) 10 15 75 57 68 46 15
The purpose of an air cushion is not to reduce the speed of a piston as it nears the stroke end.
MXW MXP Air-hydro Copper Free MG Low hydraulic pressure cylinder under 1.0MPa Through the concurrent use of a CC Series air-hydro unit, it becomes possible to operate at a constant or low speed or to effect an intermediate stop, just like a hydraulic unit, while using pneumatic equipment such as a valve.
A 1.MGTM63-35st is made by installing a 15mm spacer inside a MGTM63-50st, however the overall length will be the same as the 50st. 7069 6283 5498 4712 3927 3142 2356 OUT 7854 1571 7854 100 30 6432 5718 5003 4288 3574 2859 2144 IN 7147 1429 7147 1N: Approx. 0.102kgf 1MPa: Approx.1.02kgf/cm2 Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm2) Weight Table Additional Bracket Weight
(23.9) 18 30 24.5 EB P EA 2 x 2.2 die-cast hole (For manifold gasket positioning) 36 1/8 (EA, EB port) 1471 SYA3000/5000/7000 Series Dimensions/SYA7000 Series: Base Mounted 3/8, 1/4 (A, B port) 21 22.5 2 position single 11.5 13.5 SYA714002 03 57 77.5 42 10.4 61 M5 x 0.8 (Pilot port) B A PE 38 46 B A Manual override P EB EA 21 69 6.4 2 x 4.3 (For mounting) 87.5 1.8 (Ventilation hole) 26.5