MLGP Drop prevention for press fitting jig Drop prevention for lifter Holding a clamped condition LOCK LOCK LOCK 9-11-1 2 Drop prevention is possible within the entire stroke at any position Can be locked at any desired position Low profile with compact lock unit Easy manual unlocking Drop prevention for mid-stroke emergency stops Locking position can be changed in accordance with the Locked
Note 2) To insert the T-nuts, remove the covers at both ends of the body and insert them into the T-slots.
When the air release is complete, operate the cylinder at reduced pressure, then gradually increase it to the normal operating pressure. 5. Since CHQB series does not have an air release plug, release air from other components (e.g. from piping, etc.) as well. 6. When mounting the cylinder body with mounting bolts, use the tightening torques in the table at right as a guide.
In this case, the cylinder could operate at extremely high speeds if the cylinder bore size is small.
When fixing a work piece at the end of the piston rod, first retract the piston rod to the back end. Use the spanner hook at the end of the rod to keep the torque below the allowable tightening torque. 3. Always apply the piston rod load in the axial direction. Avoid operation where rotational torque is applied.
Metric size Inch size 3.2 01 03 05 07 09 11 23 04 06 08 10 1/8" 5/32" 3/16" 1/4" 5/16" 3/8" Control type 4 6 8 10 0 1 Meter-out Meter-in Use 1/8" tube.
100 200 205 Inch size M5 standard 1/8 standard 1/4 standard 3.2 23 04 06 08 01 03 05 07 09 1/8" 5/32" 3/16" 1/4" 5/16" 4 6 8 Use a 1/8" tube.
F B With pressure at head side With pressure at rod side *Refer to p.5.3-2 for further information on the auto switch.
Plate cylinder with lock Traditional cylinder Plate Cylinder with Lock Series MLU Series MLU 25, 32, 40, 50 Drop prevention is possible at any point of stroke. Cylinder can be locked at any desired position. Drop prevention for middle stroke emergency stops Lock positions can be changed to accommodate the position of the external stopper and the thickness of the clamped work piece.
23 SE1-01-16/-17 I Z I Z SE1-01-16C/-17C Pressure setting trimmer 2 Pressure setting trimmer 1 Pressure setting trimmer 2 Pressure setting trimmer 1 SET1 SET2 L L H H 15 SET1 SET2 L L H H 15 Indicator light (Red, Green) 23 Indicator light (Red, Green) 23 600 (3000) 56.5 600 (3000) 49 8.5 47 47 3.5 3.5 8.5 2-3.5 Mounting hole T1: NPTF 1/8 01: R 1/8 M5 x 0.8 depth 5 Piping port M5 x 0.8 depth
CDH10 U L CX CZ ZZ + Stroke Z + Stroke RR (mm) Stroke range Bore size (mm) U RR +0.3 +0.1 L CDH10 CX CZ Z ZZ 20 25 32 40 50 63 80 Up to 250 Up to 350 Up to 600 Up to 600 Up to 700 Up to 900 Up to 900 14 14 17 17 26 26 30 10 10 14 14 22 22 25 14 14 20 20 30 30 32 28 28 40 40 60 60 64 8.5 11 12 15 18 23 28 23 23 30 30 42 42 50 129 151 185 208 237 263 298 137.5 162 197 223 255 286 326 8-25-24
IZF 21 IZF 31 Extensive static neutralization At maximum flow rate 300 mm 300 mm 300 mm 4 s 6 s 6 s 8 s 0 8 s 0 2 s 4 s 2 0 2 s 300 mm 300 mm 300 mm 0 400 Insta 0 400 800 1200 1600 2000 Installation distance [mm] 0 400 800 1200 1600 2000 Installation distance [mm] At maximum flow rate, with adjustable louver/widest angle At maximum flow rate, with adjustable louver/narrowest angle 300 mm
At this time, the port on the head side is in the discharged state and is at atmospheric pressure. wLocking style manual release Push the M/O knob and turn it 90 counterclockwise. The lock disengages when the mark on the cap is aligned with the OFF mark on the M/O knob (and the lock will remain disengaged).
Parameter setting (Driver side) . 23 4.1 power supply specifications . 23 4.2 Overtravel . 23 4.3 Rotation Direction . 24 4.4 Electronic Gear . 25 4.4.1 List of the electronic gear setting for each actuator . 26 4.5 Positioning Completed Width . 27 4.6 Regenerative Resistor . 27 5.
Be certain to turn on the power supply when the flow rate is at zero. Allow an interval of 10 minutes after turning on the power, as there are some changes in the display. 5. Flow rate unit The switch measures at mass flow rates without being influenced by temperature and pressure.
Note 4) The figure shows these dimensions when the adjustment bolt is lowered (when energy absorption is at its maximum).
1 For details about certified products conforming to international standards, visit us at www.smcworld.com. The VX series will be revised shortly. Pilot Operated 2 Port Solenoid Valve For Air, Gas, Water and Oil Series VXD21/22/23 Wide variations of combination. Able to control a wide variety of fluids.
Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Note 4) Based on JIS C 0920.
Mark C on the unit Mark B at cable end Mark A at cable end (1) (2) (3) End plate bracket (EX600-ZMA2) DIN rail mounting groove 1 Intermediate reinforcing brace (EX600-ZMB2) Intermediate reinforcing brace (EX600-ZMB1) Lock screw: No.4-40 UNC DIN rail 2 End plate bracket (EX600-ZMA2) 5 Connector pin assignment Digital input unit 3 4 3 2 1 1 0 EX600-DX B/DX D EX600-DX C 25 24 23 22 21 20 19
Example Calculate the maximum effective air consumption of a 63 cylinder at an average speed of 500 mm/s. The working pressure is 0.6 MPa.