AS-FPQ/AS-FPG

Metric sizes Type 4 6 8 10 12 04 06 08 10 12 2 Elbow Control type 0 1 Meter-out Meter-in Port size M5 x 0.8 1/8 1/4 3/8 1/2 M5 01 02 03 04 With One-touch fitting Clean specification Metal part material Q G Brass (electoless nickel plated) Stainless steel (SUS304) Needle Valve/Flow Characteristics AS121FP-M5 AS221FP-01 AS221FP-02 08,10 06,08 06 04 04 AS321FP-03 AS421FP-04 12 10 10,12 08 06

Digital Flow Switch Series PFA For Air Series PFW For Water

1/8 1/4 3/8 1/2 PFA510, 550 PFA511, 521 PFA551 Specifications PFA511 PFA521 PFA551 PFA510 PFA550 Model Measured fluid Dry air, N2 Detection type Heater type 20 to 200l/min 50 to 500l/min 10 to 100l/min 1 to 10l/min 5 to 50l/min Flow rate measurement range Operating pressure range 0 to 0.5MPa Withstand pressure 1.0MPa 3kPa (at 50l/min) 3kPa (at 100l/min) 10kPa (at 200l/min) 30kPa (at 500l

KJ

Use to connect tubes at right angles. P. 6 KJY P. 4 KJL P. 8 KJR Gasket/10-32 UNF seal on thread Part no.: M-10/32G Material: Stainless steel 304, NBR Precautions Be sure to read before handling.

PA3000/5000/PAX1000

Recommended valve/for PB1013 air operated type: SYJ34 Note 2) After initial suction of liquid operating at 1 to 7Hz, it can be used with operation at lower cycles.

Refrigerated Air Dryer

This saves additional electrical wiring at the time of installation.

Process Pump Series PA3000/5000/PAX1000 Series PB1000

Recommended valve/for PB1013 air operated type: SYJ34 Note 2) After initial suction of liquid operating at 1 to 7Hz, it can be used with operation at lower cycles.

Process Pump Series PA3000/5000/PAX1000 Series PB1000

Recommended valve/for PB1013 air operated type: SYJ34 Note 2) After initial suction of liquid operating at 1 to 7Hz, it can be used with operation at lower cycles.

CC

1 Air-hydro Unit Series CC hydraulic unit, operating at a constant speed during starting or in the presence of load fluctuations, and at the same time solving the problems of sticking and slipping associated with low speed operations.

2-Apr-01 Quick Reference Auto Switch Chart with (PnP) M-8 (3 pin) & M-12 (4 pin) Connectors, Page 1/2 32, 40, 50, 63, 80 & 100 Bore sizes (Auto Switch Spacer # BMP1-032 required) 32, 40, 50, 63, 80, 100, 125 & 200 Gripper Bore sizes (sizes depend on seri

M-8 M-12 SMC Type of 2-Apr-01 SMC Quick Reference Auto Switch Chart with (PnP) M-8 (3 pin) & M-12 (4 pin) Connectors, Page 1/2 The above older MDB1 Direct Body Mount 32, 40, 50, 63, 80 & 100 Bore sizes (Auto Switch Spacer # BMP1-032 required) our new part # MHL, Direct Body Mount 10, 16, 20, 25, 32 & 40 Gripper Bore sizes -Y7PSDPC MHQG2 Direct Body Mount 32 & 40 Gripper Bore sizes MHS2/3/

4 Way • 4 and 5 Port, Rubber Seal • Solenoid Pilot Valve, Series SYJ3000

Seal the unused "R" port at the end of the manifold.

ARM10/11

can damage the switch. 24V DC Load connection side: 0.5 m 3.

ARM10/11

can damage the switch. 24V DC Load connection side: 0.5 m 3.

5 Port Air Operated Valve Series VFA3000 1

Not required Lubrication Mounting orientation Free Impact/Vibration resistance (m/s2) Note) 300/50 Note) Impact resistance: No malfunction from test using drop impact tester, to axis and right angle directions of main valve, each one time when pilot signal is ON and OFF .

Guide Cylinder Series MGG ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 1

Manual release, Lock type While pushing the M/O knob, turn it 90 counterclockwise. The lock is released (and remains in a released state) by aligning the mark on the cap with the OFF mark on the M/O knob. When locking is desired, turn M/O button clockwise 90 while pushing fully, correspond on cap and ON mark on M/O button. The correct position is confirmed by a click sound click.

Air-hydro Unit

Operation at a piston speed of 180 mm/sec with a size 80 cylinder bore. (Operating pressure: 0.5 MPa, Load mass: No load, Piping: I.D. 19 mm x length 1 m) Air-hydro Unit CC Series Air-hydro Converter CCT Series Valve Unit CCVS/CCVL Series Application Example 1.

MXW

Amount of displacement on A when the load is applied at F. Amount of displacement on A when the load is applied at F.

Series VC, Series VCS, Direct Operated 2 Port Solenoid Valve for Steam

2 Port for Steam Dimensions (mm) 1in = 25.4mm Grommet: G Conduit: C Q Approx. 300 F D Approx. 280 D Q F C G (PF) 1/2 C R R E E B A H 2-P Port size 2-P A B H 2-M Port size 2-M Thread depth N L L K K Conduit terminal: T F (Q) 34 25 U R C G (PF) 1/2 E B A H D 2-P Port size (S) 2-M L K N.C.

MLGC

Characteristics Maximum piston speed: 500 mm/s It can be used at 50 to 500 mm/s provided that it is within the allowable kinetic energy range. Air cushion is standard. Enables the impact to be absorbed at the stroke end when the cylinder is operated at high speeds. Cylinder position can be detected.

MLGC

Characteristics Maximum piston speed: 500 mm/s It can be used at 50 to 500 mm/s provided that it is within the allowable kinetic energy range. Air cushion is standard. Enables the impact to be absorbed at the stroke end when the cylinder is operated at high speeds. Cylinder position can be detected.

MGC

Rush speed into cushion is as follows: M + m 2 = 1.4a Ek = 2 Ek: Kinetic energy (J) M: Weight for the driven object (kg) m: Weight for movable part of cylinder (kg) : Maximum speed (m/s) a: Average speed (m/s) = 1.4 x 300 = 420 mm/s. Note) Set a so that rush speed into cushion should not exceed 0.75 m/s.