Swivels D Swivels Male Pipe Female Pipe A Part Number A B Dia.
Select between two values 2-A or 1-A using the + and keys. The value 2-A indicates a double acting actuator and 1-A a single acting actuator. To conclude press the ?
Common IN Individual IN Common IN Individual IN Bonnet Polyacetal w o ARM2500 -A-02 ARM2500 -B-02 ARM3000 -A-03 ARM3000 -B-03 1 Regulator Regulator Replacement Parts 1 1 1 End plate R End plate L O-ring !0 !1 !2 Description Material Part no. No.
Common IN Individual IN Common IN Individual IN Bonnet Polyacetal w o ARM2500 -A-02 ARM2500 -B-02 ARM3000 -A-03 ARM3000 -B-03 1 Regulator Regulator Replacement Parts 1 1 1 End plate R End plate L O-ring !0 !1 !2 Description Material Part no. No.
Air filter (5m or less) When using a solenoid valve, use a metal seal type (series VQ, VQZ, SQ, etc.).
Dont use a wrench on push-to-connect end. 2 2 Cut tubing square with a clean 90 edge Dont use excessive tube angle cut which can lead to leakage or breaking. 90 90 3 3 Use SMC Tube Cutters Dont use dikes, a knife, a saw or a dull tool to cut the tubing.
Silencer AN200-02 AN200-02 AN300-03 AN300-03 AN400-04 Caution on Pneumatic Circuit Design Air balance Unlike the current pneumatic cylinder that performs a simple reciprocal movement, the stroke reading cylinder with a brake also makes intermediate stops.
D-A59W D-Z7/Z80 D-M9/M9W D-M9A Bore size (mm) Bore size (mm) D-Z7/Z80 D-A5/A6 A B A B A B A B A B A B Ht Hs Ht Hs Ht Hs Ht Hs Ht Hs 40 50 63 80 100 40 50 63 80 100 11.5 8.5 8 5 13 10 5 2 27 28.5 27 34 35.5 28.5 29 27 13 8 9.5 4.5 14.5 9.5 6.5 1.5 33 33.5 33 38.5 39.5 34.5 33 33 4.5 0 8.5 3.5 47.5 38.5 14.5 9.5 11 6 16 11 8 3 38.5 38 38.5 43.5 45 38.5 28 37 8.5 3.5 12.5 7.5 54
Auto switch model Bore size [mm] 20 25 32 40 D-M9m(V) D-M9mW(V) BM8-020 (A set of a, b, c, d) BM8-025 (A set of a, b, c, d) BM8-032 (A set of a, b, c, d) BM8-040 (A set of a, b, c, d) BM8-025S (A set of a, b, c, d) * S: Stainless steel set screw BM8-032S (A set of a, b, c, d) * S: Stainless steel set screw BM8-040S (A set of a, b, c, d) * S: Stainless steel set screw D-M9mA(V) BM8-020S (A
Double acting PA PA B A PB B A With by-pass Suck back valve Manual Operation-Series LVH N.C. Double acting P PA PA Locking and non-locking types available B A B A PB B A Integral fitting type/Threaded type Manifolds Main applications and fields For shut off For air bleeding N.C.
Cover Rod cover Unit holding tie-rod A (2 depth 1 mm hole is on the side of tie-rod for attaching unit A.)
When ordering only a vessel, it is not necessary to enter the symbol for built-in elements. The membrane element cannot be selected for FGH100. Port size 03 04 06 10 Rc3/8 Rc1/2 Rc3/4 Rc1 Since this product uses PTFE for gasket material, a large torque is required to tighten a clamp ring. The FKM specification with the clamp ring tightening torque reduced is also available.
When ordering only a vessel, it is not necessary to enter the symbol for built-in elements. The membrane element cannot be selected for FGH100. Port size 03 04 06 10 Rc3/8 Rc1/2 Rc3/4 Rc1 Since this product uses PTFE for gasket material, a large torque is required to tighten a clamp ring. The FKM specification with the clamp ring tightening torque reduced is also available.
(A) 2 1 (P) 3 (R) Rubber seal type VQZ200 300 / Metal seal type 3 2 1 3 2 1 N.C. N.C. (A) 2 (A) 2 3 (R) 1 (P) 3 (R) 1 (P) 3 2 1 3 2 1 N.O. (A) 2 N.O. (A) 2 3 (R) 1 (P) 3 (R) 1 (P) Parts list No.
Never mount a switch in a place that will be used as a scaffold during piping work. Damage may occur if subjected to an excessive load. Especially when the switch supports piping, do not apply a load of 15Nm or more to the metal part of the switch. 11. Provide a section of straight pipe of at least 8 times the pipe diameter in the piping before and after a switch.
Through the use of a booster, a pressure that is higher than that of the main air passage can be supplied.
When mounting a coupler on equipment where impact and vibration occur, install a hose with a length of 300mm or more between the equipment and the coupler. 3. To prevent an unexpected disconnection of the coupler, operate with the sleeve lock mechanism in the locked condition. 4. Install a stop valve at the supply pressure side of the socket.