IDG Note) When the symbol C or D is designated, the same part number of an auto-drain listed on page 14-19-33 will come together.
Do not operate with the stroke adjustment unit fixed in an intermediate position. When the stroke adjustment unit is fixed in an intermediate position, slippage can occur depending on the amount of energy released at the time of an impact. In that case, use a short spacer or a long spacer. For other lengths, please consult with SMC.
Refer to p.0-39 to 0-46 for Safety Instructions and common precautions. Operating Pressure Use Recommended Air Pressure Circuit. Caution Caution It is necessary to make it lock and unlock properly. q Supply air pressure of 0.15MPa or higher to the port on the side that has the lock mechanism, as it is necessary for disengaging the lock.
Do not use in an atmosphere of corrosive gases, chemicals, sea water, water or water vapor or in an environment where such substances may adhere. 2. Provide shading in an environment where the product is exposed to the sunlight. 3. Do not use in an environment where a heat source is at a close distance. 4. Do not use in an environment where static electricity is a problem.
(Ex.: 2504-N002) Construction/Parts/Dimensions AN103 AN203 Construction/Parts/Dimensions VEX AN AMC AN303/403 AN200 to 900SAN, #1 to #8 AN202 to 402SAN, #9 to #11 AN103 to 403SAN, #12 to #15 5.2-2 ANm00/ANm02/ANm03/25/AN (BC Sintered Body) Series AN Ideal for the exhaust of a compact valve or pilot air.
In the case of obtaining an accurate flow rate, refer to front matter pages 1 to 6.
Note 3) The figure shows an extended piston rod.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. Limited warranty and Disclaimer 1.
16 20 25 32 36 46 60 70 16 20 25 32 36 46 16 20 25 32 36 46 17 20 20 12 12 17 17 20 20 27 27 12 12 17 17 20 20 22 22 22 22 30 30 56 65 73 36 40 48 56 65 73 92 103 36 40 48 56 65 73 36 40 48 56 65 73 4 x M12 x 1.75 4 x M16 x 2 4 x M16 x 2 0 50 342 87 435 255 100 56 4.6 106 150 4 x M10 x 1.5 23 40 (1 1/2B) 50 (2B) 0 60 450 94 545 356 120 70 6.4 120 155 4 x M12 x 1.75 28 0 219 62
This may cause deformation of the non-rotating guide, abnormal responses of the auto switch, play in the internal guide or an increase in the sliding resistance.
(mm) Mounting Bore size 20-MGG Bearing type Stroke X Y Q Bore size (mm) Copper-free 39 86 (94) 25 32 Specifications 46 96 (105) 29 40 20, 25, 32, 40, 50, 63, 80, 100 Bore size (mm) 57 109 (121) 31 50 Double acting Action 56 112 (124) 34 63 Air 68 137 (151) 46 Fluid 80 Maximum operating pressure 1.0MPa 68 138 (152) 47 100 Minimum operating pressure 0.15MPa (horizontal with no load) Dimensions
46 e Valve Model Fill in the blanks below with symbols of necessary specifications.
When the fitting is removed from the tubing, the chuck and collet are released, thus preventing them from biting into the tube to an unnecessary degree. Accepts nylon, soft nylon and polyurethane tubes. Has high retaining force. Packing Tube Can be used for a wide range of pressure from a low vacuum up to a pressure of 145psi {1.0MPa }.
(mm) Electrical entry P Port size A B C D E F H K L M Model Grommet: G Conduit: C DIN connector: D Conduit terminal: T Q R Q R Q R S Q R S 13.5 28 64 31 6.5 12.5 28 14 12.8 M4 22 45 44 43 58 40.5 46.5 99 43 66 1/8 VCW21 18 36 67 31 8.5 12.5 28 18 12.8 M4 22 46 44 44 58 41.5 46.5 99 44 66 1/4 22 40 80.5 36.5 11 15 32 20 19 M5 24 56.5 46 54.5 60 52 48.5 101 54.5 68 1/4, 3/8 VCW31 30 50 85.5
Please contact SMC for a specification sheet when placing an order.
Mixed single and double wiring is available as an option.
Install an air dryer, after cooler, etc. Air that includes excessive condensate may cause malfunction of valves and other pneumatic equipment. To prevent this, install an air dryer or after cooler etc.. 3. If excessive carbon dust is generated, eliminate it by installing mist separators at the upstream side of valves.
optional manifotd mounted deslgn is available tor the NVS 3115 valves, The block 13 aluminum bar Etock with common supply and exhaust as wellaa an individual outlet port on the side.
Besides, the whole accuracy after mounting on an equipment may be varied depending on the mounting condition and surroundings. As an equipment, calibration should be done by customer.
Besides, the whole accuracy after mounting on an equipment may be varied depending on the mounting condition and surroundings. As an equipment, calibration should be done by customer.