1 Blow Gun Series VMG K M H D MS Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com T VMG Pressure loss is less than 1%. (nozz Do not use in an atmosphere of corrosive gases, chemicals, sea water, water or water vapor or in an environment where such substances may adhere. 2. Provide shading in an environment where the product is exposed to the sunlight. 3. Do not use in an environment where a heat source is at a close distance. 4. Do not use in an environment where static electricity is a problem.
(Ex.: 2504-N002) Construction/Parts/Dimensions AN103 AN203 Construction/Parts/Dimensions VEX AN AMC AN303/403 AN200 to 900SAN, #1 to #8 AN202 to 402SAN, #9 to #11 AN103 to 403SAN, #12 to #15 5.2-2 ANm00/ANm02/ANm03/25/AN (BC Sintered Body) Series AN Ideal for the exhaust of a compact valve or pilot air.
In the case of obtaining an accurate flow rate, refer to front matter pages 1 to 6.
Note 3) The figure shows an extended piston rod.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. Limited warranty and Disclaimer 1.
16 20 25 32 36 46 60 70 16 20 25 32 36 46 16 20 25 32 36 46 17 20 20 12 12 17 17 20 20 27 27 12 12 17 17 20 20 22 22 22 22 30 30 56 65 73 36 40 48 56 65 73 92 103 36 40 48 56 65 73 36 40 48 56 65 73 4 x M12 x 1.75 4 x M16 x 2 4 x M16 x 2 0 50 342 87 435 255 100 56 4.6 106 150 4 x M10 x 1.5 23 40 (1 1/2B) 50 (2B) 0 60 450 94 545 356 120 70 6.4 120 155 4 x M12 x 1.75 28 0 219 62
This may cause deformation of the non-rotating guide, abnormal responses of the auto switch, play in the internal guide or an increase in the sliding resistance.
(mm) Mounting Bore size 20-MGG Bearing type Stroke X Y Q Bore size (mm) Copper-free 39 86 (94) 25 32 Specifications 46 96 (105) 29 40 20, 25, 32, 40, 50, 63, 80, 100 Bore size (mm) 57 109 (121) 31 50 Double acting Action 56 112 (124) 34 63 Air 68 137 (151) 46 Fluid 80 Maximum operating pressure 1.0MPa 68 138 (152) 47 100 Minimum operating pressure 0.15MPa (horizontal with no load) Dimensions
46 e Valve Model Fill in the blanks below with symbols of necessary specifications.
When the fitting is removed from the tubing, the chuck and collet are released, thus preventing them from biting into the tube to an unnecessary degree. Accepts nylon, soft nylon and polyurethane tubes. Has high retaining force. Packing Tube Can be used for a wide range of pressure from a low vacuum up to a pressure of 145psi {1.0MPa }.
(mm) Electrical entry P Port size A B C D E F H K L M Model Grommet: G Conduit: C DIN connector: D Conduit terminal: T Q R Q R Q R S Q R S 13.5 28 64 31 6.5 12.5 28 14 12.8 M4 22 45 44 43 58 40.5 46.5 99 43 66 1/8 VCW21 18 36 67 31 8.5 12.5 28 18 12.8 M4 22 46 44 44 58 41.5 46.5 99 44 66 1/4 22 40 80.5 36.5 11 15 32 20 19 M5 24 56.5 46 54.5 60 52 48.5 101 54.5 68 1/4, 3/8 VCW31 30 50 85.5
Please contact SMC for a specification sheet when placing an order.
Mixed single and double wiring is available as an option.
Install an air dryer, after cooler, etc. Air that includes excessive condensate may cause malfunction of valves and other pneumatic equipment. To prevent this, install an air dryer or after cooler etc.. 3. If excessive carbon dust is generated, eliminate it by installing mist separators at the upstream side of valves.
optional manifotd mounted deslgn is available tor the NVS 3115 valves, The block 13 aluminum bar Etock with common supply and exhaust as wellaa an individual outlet port on the side.
Besides, the whole accuracy after mounting on an equipment may be varied depending on the mounting condition and surroundings. As an equipment, calibration should be done by customer.
Besides, the whole accuracy after mounting on an equipment may be varied depending on the mounting condition and surroundings. As an equipment, calibration should be done by customer.
Measurement mode screen If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system Check the product regularly for proper operation Otherwise malfunction can result, causing an accident.
RSG series (Adjustable mounting height type) 40, 50 Numerous variations Equipped with an easy-tomaintain shock absorber. The shock absorber incorporated in the lever type is adjustment-free and easy-to-maintain. (32, 40, 50) It is possible to select option for many applications.
Cannot be used as an emergency shutoff valve, etc. The valves presented in this catalog are not designed for safety applications such as an emergency shutoff valve. If the valves are used in this type of system, other reliable safety assurance measures should also be adopted. 2.