Single Axis Electric Actuator Serriies LJ1S Slider Guide Main parts Controller Intermediate strokes For manufacture of strokes other than the standard strokes above, add "-X2" at the end of the part number.
The magnetic coupling will break if operated at a pressure exceeding these limits. When stopping a load using an air pressure circuit, operate at or below the kinetic energy shown in the table below. The magnetic coupling will break if the allowable value is exceeded.
Note 4) Vibration resistance No malfunction when tested with one sweep of 5 to 200 Hz in the axial direction and at a right angle to the armature, in both energized and deenergized states. Impact resistance Nomalfunction when tested with a drop tester in the axial direction and at a right angle to the armature, one time each in energized and deenergized states.
A B L1 L2 14 12 A PA B A B 14 SMC A PA B A B A PA 40 (53) L-side R-side L-side R-side (2n-1/8) D-side D-side 14 34 103 2 103 174.5 (Single) 4n-3/8, 1/2 2, 4 port 94 62 59 17 174.5 (Single) 216.5 (Double) 216.5 (Double) 221.5 216.5 (3 position) 221.5 216.5 (3 position) Bottom ported M12 connector L: Dimensions n: Stations n P, R1, R2 port 2 3 4 5 6 7 8 9 10 1 Formulas L 157 L1 L2 L1 L2 176
Liquid dripping: 0.02 to 0.77 cm3 at each removal Aeration: 0.1 to 2.7 cm3 at each removal DM KDM KB Socket valve Plug valve KR KA KQG2 KG KFG2 MS KKA KKA KP LQ MQR T Non-greased specification (standard) Allows smooth installation and removal even without grease O-ring: Fluorine coated Sliding parts of plug and socket: Fluorine coated is used.
Furthermore, when pipe tape is used, leave 1.5 to 2 thread ridges exposed at the end of the threads.
Table yaw deflection due to static yaw moment applied at arrow for fully extended stroke of slide table. Table yaw deflection due to static yaw moment applied at arrow for fully extended stroke of slide table.
Dynamic moment Va Calculation Example m Operating conditions Cylinder: CYV32 Mounting: Horizontal wall mounting Maximum speed: U = 300 [mm/s] Load mass: m = 1 [kg] (excluding mass of the arm section) L1 = 50 [mm] L2 = 50 [mm] L2 L1 Item Load factor n Note 1. Maximum load mass m 1 = m/m max = 1/5 = 0.20 L2 Review m. L1 2.
To install/remove the product, use an appropriate wrench to tighten/loosen at the supplied nut on body B. 12. Mounting Do not apply torque at other points as the product may be damaged. Rotate body A manually for positioning after installation. Warning 1.
For the maximum allowable load mass for each piston speed, please refer to Graph (1). 1600 26 25 23.5 The above value represents the applicable load at the position where the moment does not work at the time of stop. Factors such as impact, etc. are not in consideration with the value.
(coil temperature 20C, at rated voltage, without surge voltage suppressor) When equipped with DC solenoid/surge voltage suppressor, a delay of about 20 to 30msec occurs in the OFF response time.
VQZ Plug Lead Unit U Type (Large Flow Capacity) Mounted Manifold (VV3Q12U) VZ L1 L2 7 4-PT1/8 VS P, E port 7 16 P E P E 29 14 7 32 40.1 49.8 300 Round head screw M1.7 X 14 2-3.5 Mounting hole Manual override 15.5 P=10 300 n 5 4 3 2 1 U side D side 46.5 35.2 19.4 15.5 A A 9.5 16.7 P=10 n-M5 A port Dimensions Equation: L1=10n+21 L2=10n+7 n: Station (Max. 20 stations) n L L1 L2 1 31 17
(Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed at both energized energized states in the axial direction and at the right angles to the main valve and armature.
= 50 [mm] D-X L2 L1 20Data Item Load factor n Note 1.
Do not short-circuit these terminals. [1] Main circuit power input terminals, L1, L2 and Control power input terminals, L1, L2: Connect the 200VAC external power supply to the power supply. Refer to the power supply specification for the size of the acceptable electric wire. [2] Connect the motor cable (U, V, W) to the servomotor connection terminals (U, V, W).
L2 [mm] L2 [mm] L2 [mm] L2 [mm] 600 600 600 600 Y 400 400 400 400 Mer m 200 200 200 200 0 0 0 0 0 10 20 30 40 50 0 10 20 30 40 50 60 0 2 4 6 8 10 12 14 16 0 4 8 12 16 20 24 Work load [kg] Work load [kg] Work load [kg] Work load [kg] 2000 2000 2000 2000 Mep 1500 1500 1500 1500 L3 [mm] L3 [mm] L3 [mm] L3 [mm] m 1000 1000 1000 1000 L3 Z 500 500 500 500 0 0 0 0 0 10 20 30 40 50 0 2 4 6 8 10
Note 4) Vibration resistance No malfunction when tested with one sweep of 5 to 200Hz in the axial direction and at a right angle to the armature, in both energized and de-energized states. Impact resistance .. No malfunction when tested with a drop tester in the axial direction and at a right angle to the armature, one time each in energized and de-energized states.
(Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed at both energized energized states in the axial direction and at the right angles to the main valve and armature.
Applicable bore size Dd9 L1 L2 m d Drill through Included split pin Included flat washer Clevis Knuckle 2 x d Dd9 CDP-2A 40 10 0.040 0.076 46 38 4 3 3 x 18 L Polished round 10 L1 L2 m L1 L2 m CDP-3A 50 40, 50, 63 12 0.050 0.093 55.5 47.5 4 3 3 x 18 L Polished round 12 2 x d Dd9 CDP-4A 63 16 0.050 0.093 71 61 5 4 4 x 25 L Polished round 16 L1 L2 m CDP-5A 80 18 0.050 0.093 76.5 66.5 5 4