Material: T (SCS14 Cover, SS 316 Case, Fluororesin Gasket/O-ring, Fluororesin Seal), Element Length: B [ℓ500 (ℓ250 x 2)], Port Size: 06 (3/4 Rc), Element Type: B (Sintered Metal, Bronze Material), Nominal Filtration Accuracy: 20 μm, Element Seal Material: T (Fluororesin), Accessory: B (Bracket)
Seal), Element Length: B [ℓ500 (ℓ250 x 2)], Port Size: 06 (3/4 Rc), Element Type: B (Sintered Metal, Bronze Material), Nominal Filtration Accuracy: 10 μm, Element Seal Material: N (NBR), Accessory: B (Bracket), Made to Order: X77 (Differential Pressure Indicator)
Material: C (Aluminum Cover, SPCD Case, NBR Gasket/O-ring, Nylon Seal), Element Length: B [ℓ500 (ℓ250 x 2)], Port Size: 04 (1/2 Rc), Element Type: B (Sintered Metal, Bronze Material), Nominal Filtration Accuracy: 5 μm, Element Seal Material: N (NBR), Accessory: B (Bracket)
Process valve series VNC, Air operated type, Orifice size: 7mm to 80mm, Port size: 1/8 to 2 Rc(PT), Seal material: NBR, FPM, EPR, VNA/B/C/D, VALVE, VNA/B/C/D 2-WAY MEDIA VALVE, 1A, VNA/B/C/D
SI unit for EtherNet/IP TM . : Standard wiring of the manifold is for double-solenoid valves and the output number starts at the A side and then B side in that order as shown in the figure a.
SPEEDCON connector wiring method is explained below. (1)Align the mark B on the metal bracket of the cable side connector (plug/socket) with the mark A. Wiring Setting and Adjustment OFF OFF OFF OFF OFF (3)When the mark B of the connector has been turned 180 degrees (1/2 turn), wiring is completed. Confirm that the connection is not loose.
To obtain the operation manual about this product and control unit, please refer to the SMC website (URL http://www.smcworld.com) or contact SMC directly. 2 Display cover Open at the switch configuration. (3)When mark B has been turned 180 degrees (1/2 turn), wiring is complete. Confirm that the connection is not loose.
Verify the specifications before use. 5 Branch port B (COM B) 4 (Input: Max. 32 points/Output: Max. 32 points per branch) Number of branches Connect the SI unit (with manifold valves) or input unit using a branch cable.
L/A OUT L/A IN 2 Display cover Open to access the setting switches. (3)When mark B has been turned 180 degrees (1/2 turn), wiring is complete. Confirm that the connection is not loose. If turned too far, it will become difficult to remove the connector. Displays the communication status of the BUS OUT side physical layer.
An injury can result. 3 Power supply for input and control: 24 VDC 10% Power supply for solenoid valves: 24 VDC +10%/-5% Power supply voltage range 4 Branch port A (COM A) L 5 Branch port B (COM B) Power supply for input and control: 6.2 A (GW unit internal current consumption: 200 mA or less) Power supply for solenoid valves: 4 A Connect the SI unit (with manifold valves) or input unit using
L/A OUT L/A IN Displays the communication status of the BUS OUT side. 2 Display cover The display cover should not be opened. (3)When mark B has been turned 180 degrees (1/2 turn), wiring is complete. Confirm that the connection is not loose. If turned too far, it will become difficult to remove the connector.
SPEEDCON connector wiring method is explained below. (1)Align the mark B on the metal bracket of the cable side connector (plug/socket) with the mark A. Wiring 3 4 1 2 (3)When the mark B of the connector has been turned 180 degrees (1/2 turn), wiring is completed. Confirm that the connection is not loose.
For removal, release the catch with a screwdriver in the direction of the arrow shown in Fig. b. Refer to the SMC website (URL http://www.smcworld.com) for more information about troubleshooting.
A B Press the or button to change the set value. The button is to increase and the button is to decrease the set value. 2 B D D Press the button continuously to keep increasing the set value.
. -28No.LFE*-OMZ0012 Analogue output Flow/Analogue output Output A B C Voltage output 1 V 1.1 V 5 V C Current output 4 mA 4.4 mA 20 mA Rated flow [L/min] Model B Minimum Maximum A LFE1 0.5 20 LFE2 2.5 100 Flow rate 0 Minimum Maximum rated flow LFE3 5 200 rated flow Out of range -29No.LFE*-OMZ0012 Dimensions 2XPort size Note) The electrical entry for lead wire with M12 connector does not rotate
Peak hold: "P" Bottom hold: "b" LCD Charge amount Peak/Bottom hold value IZH10 Thank you for purchasing an SMC IZH10 Series Handheld Electrostatic Meter. Please read this manual carefully before operating the product and make sure you understand its capabilities and limitations. Please keep this manual handy for future reference.
Note 2) Operation is possible with a valve with small Cv value when the operation cycle is small. 12 How to Order P B 1 3 1 3 A S Female thread / Tube extension P B 1 3 1 3 A S With nut Port size Material of diaphragm Symbol Main fluid Pilot air Symbol Material of diaphragm connection size connection size Female thread 1 PTFE 01 Rc 1/8 N01 NPT 1/8 F01 G 1/8 Actuation Tube extension Symbol
Body size Symbol Symbol diameter 22 mm 26 mm 32 mm 5 6 16A 20A 25A 16 mm 22 mm 5 6 LVP6 Symbol Pilot port thread (fitting) type A Symbol Nil 1 2 N Thread (fitting) type 6 mm One-touch fitting Rc1/8 M5 x 0.8 NPT1/8 PA B N.C. A PB Option B Applicable valve type N.C. N.O. Double acting N.O.
B Sets alarm which is selected for contact output 3. [-] is displayed when the setting of the output signal of contact output3 is not selected alarm signal. ---(AL.01) Contact output signal 3 selected alarm 2.4 Setting and checking HRSH Series 2-4 HRX-OM-R028 Chapter 2 Contact input/output communication 2.4.2 Setting and checking Communication mode Setting and checking 1.
B maintenance service. If the fluid is left inside, an accident and damage can result during transportation. Cutoff setting G F The pump breaks. Check the pump operation. If the pump breaks, need to be replaced.