3 Port Solenoid Valve/ Made to Order Series Compatible with Secondary Batteries 1 For details about 25A-, refer to the WEB catalog Series Compatible with Secondary Batteries/Series 25A-. X536 X538 X555 How to Order 25AVP 4 5DZ1 Fill in according to How to Order above. Note) Electrical entry can be selected only for D type. Check valve type is available only when the thread type is Rc.
-25A VND50D-32A VND50D-32F VND60D-40A VND60D-40F VND70D-50A VND70D-50F 1 8 1 4 26 28 31 120 130 240 380 7 0.3 3 8 15 0.6 1 2 3 4 20 0.9 1.4 2.3 5.5 3.6 7.2 5.7 10.8 25 1 VC 1 4 1 440 32 32 1 2 1 VDW 920 40 40 2 VQ 1500 50 50 Note) The companion flange is JIS B 2210 10K (standard) or its equivalent.
P reduced pressure A reduced pressure B reduced pressure ARB350-00-P ARB350-00-A ARB350-00-B A B A B 27 Series VQ7-8 Manifold Options Interface regulator Main EXH back pressure check plate P A B ARB350-00AXT512-25A Interface regulator Main EXH back pressure check plate (AXT512-25A) 282 ARB350-00P A B 146 SMC SMC 238.5 (208) 221 226.5 (196) 209 193.5 181.5 135.5 (105) 118 PA B PE PE P 90.5
This is a legacy product, and replaced byCP96SDB32-40C
Store away from direct sunlight at 40C or less. 2. Open the inner package of the double packaging in a clean room or other clean environment. TMH ASD AS Piping AS-FE Caution KE 1. Be sure to use sealant tape or liquid gasket at the taper thread part. Using without sealant tape or liquid gasket can cause air leakage. AS-FG AS-FP AS-FP AS-FM AS-D AS-T ASP ASN AQ ASV AK VCHC ASR ASQ 715
If air with a low dew point (40C or less) is required, do not use nylon tube or resin fitting (except for fluorine resin) for the outlet side of the membrane air dryer or heatless air dryer. Nylon tubing could be affected by the ambient air and it thus might not be possible to achieve the prescribed low dew point at the end of the tube.
Store away from direct sunlight at 40C or less. 2. Open the inner package of the double packaging in a clean room or other clean environment. TMH ASD AS Piping AS-FE Caution KE 1. Be sure to use sealant tape or liquid gasket at the taper thread part. Using without sealant tape or liquid gasket can cause air leakage. AS-FG AS-FP AS-FP AS-FM AS-D AS-T ASP ASN AQ ASV AK VCHC ASR ASQ 715
If air with a low dew point (40C or less) is required, do not use nylon tube or resin fitting (except for fluorine resin) for the outlet side of the membrane air dryer or heatless air dryer. Nylon tubing could be affected by the ambient air and it thus might not be possible to achieve the prescribed low dew point at the end of the tube.
If air with a low dew point (40C or less) is required, do not use nylon tube or resin fitting (except for fluorine resin) for the outlet side of the membrane air dryer or heatless air dryer. Nylon tubing could be affected by the ambient air and it thus might not be possible to achieve the prescribed low dew point at the end of the tube.
If air with a low dew point (40C or less) is required, do not use nylon tube or resin fitting (except for fluorine resin) for the outlet side of the membrane air dryer or heatless air dryer. Nylon tubing could be affected by the ambient air and it thus might not be possible to achieve the prescribed low dew point at the end of the tube.
Fluid Standard specifications Option Note) Water (Standard, up to 40C) Air (Standard, Dry) Turbine oil Vacuum (up to 1.3 x 102 Pa) Carbon dioxide (CO2), Nitrogen gas (N2) Vacuum (up to 1.3 x 10-1 Pa) (V, M) Non-leak (106 Pam3/s or less) (V, M) JIS Symbol A C.O.
AMH850-20 IDG20-03 IDG30-03 IDG50-03 IDG75-04 IDG100-04 IDU3DIDU4DIDU6DIDU8DIDU11CIDU15CIDU22C1-3 IDU37C1-3 IDU55C-3 IDU75C-3 AMD1010-40 Note 1) Air cooled aftercooler Inlet air temperature: 60C, Ambient temperature: 32C Water cooled aftercooler Inlet air temperature: 180C Inlet temperature of cooling water: 30C Note 2) Series IDF Inlet air temperature: Saturated at 35C (IDF1D), saturated at 40C
Model LMU100 LMU200 ALF ALT Inlet air pressure Oil tank set pressure range Oil Dynamic viscosity of oil (40C) 0.1 to 1.0 MPa 0.05 to 0.2 MPa Turbine oil, Non-water soluble cutting oil (JIS, N1 type) 2 to 200 mm2/s Total capacity: 3000 Effective capacity: 2500 5 to 50C 100 VAC 50/60Hz, 200 VAC 50/60Hz, 24 VDC ALD ALB Oil tank capacity (cm3) Ambient and fluid temperature Solenoid valve voltage
Power supply Note 2) 2 x 1.5 VDC 2A alkali dry cell batteries (continuous use for 15 hours or more) Applicable cylinder Built-in magnet Enclosure IP40 Ambient temperature 10 to 60C temperature range Operating: 0 to 40C, Stored: 10 to 60C (with no freezing or condensation) Operating Environmental resistance Applicable Auto Switches for the Time Required for Stroke/ Operation Count Measurement
Specifications IZH10 Model 20.0 kV Rated charge amount range 0.1 kV (1.0 kV to 20.0 kV), 0.01 kV (0 to 0.99 kV) Minimum display unit Measurement distance 50 mm (between sensor part and measured target) Power supply Note 1) 1.5 VDC 2A alkali dry cell battery, 2 pcs (continuous use for 15 hours or more, see Note 2)) 5% F.S. 1 digit Display accuracy Enclosure IP40 Environment Operating: 0 to 40C
Model IZN10E-Cm-m Input voltage*1 100 to 240 VAC, 50/60 Hz Output voltage 24 VDC Output current 1 A max Ambient temperature Operating 0 to 40C Stored 20 to 60C Ambient humidity Operating/Stored 10 to 90%RH Standards/Directive CE, cUL *1 For the AC cord type, note that the rated voltage of the AC cord included as an accessory is 125 V (See page 13). 11 Nozzle Type Ionizer IZN10E Series Accessories
Measuring/ Counter IZS31 F X196 Heat-shrinkable tube (Output signal identification, Black for NPN, White for PNP) Applicable output specifications 1800 20 96 2000 20 12 1 NPN specification PNP specification Nil P Specifications 29 44 F.G. connection terminal Note ) Input voltage Output voltage Output current Ambient temperature Ambient humidity Weight 100 VAC to 240 VAC, 50/60 Hz 24 VDC 1A 0 to 40C
Store away from direct sunlight at 40C or less. 2. Open the inner package of double packaging in a clean room or other clean environment. Connection thread size Proper tightening torque (Nm) M R 1/8 7 to 9 R 1/4 12 to 14 H/DL L/LL R 3/8 22 to 24 R 1/2 28 to 30 KC Installation of Threads 3. Tightening tools Tighten with an appropriate wrench using the hexagon wrench flats on the body.
Possible to use in vacuum to 100 kPa Applicable Tubing Tubing material FEP, PFA, Nylon, Soft nylon, Polyurethane Tubing O.D. 4, 6, 8, 10, 12, 16 Specifications Fluid Air, Water 1 Operating pressure range 2 100 kPa to 1 MPa Proof pressure (at 23C) 3 MPa Ambient and fluid temperature 5 to 60C, Water: 0 to 40C (No freezing) Thread Mounting section JIS B 0203 (Taper thread for piping) JIS B 0205
(Full span) or less Hysteresis Pressure switch with digital display and self-contained solid state sensor 3% F.S. (5 to 40C), 5% F.S. (5 to 60C) Accuracy AF 12 to 24 VDC (Ripple 10% or less) Voltage Minimum allowable pressure indicator on digital display AR Open collector 30 V, 80 mA or less Output Light turns ON when pressure drops below the set minimum.