0.5 If an alarm continues to be generated even after cleaning, the emitters may be worn out or damaged.
A cabtire cable with an O.D. 6 to 12 mm is applicable. Tighten each part with an appropriate tightening torque shown below.
For the external pilot valve, an "R" should be attached to the valve and the manifold part number.
Therefore, if an external stopper is used to stop the piston rod and the lock is engaged, the piston rod will shift in the amount of its axial play. 6. To effect an intermediate stop, take the cylinders stopping precision and overrun amount into consideration.
An optional remote adiustment cable provides adiustment control in otherwise inaccessible locations.
Provides a stable supply of dry air even under high demand conditions with an inlet air temperature of 60C. IDU3D to 6D: 60C IDU8D to 37C1: 55C IDU55C, 75C: 50C Series IDF Can accommodate an inlet air temperature of 40C System efficiency is improved by using a high performance heat exchanger.
Spacers are used to fix the stroke adjustment unit at an intermediate stroke position.
OO PP QQ RR SS TT UU VV Model Applicable gasket ML1C25 ML1C32 ML1C40 10 14 37 24 8 27 20 8 C11.2 16.5 18 46 30 12 32 22 8 C11.2 17 23.5 12.5 10 53 40 34 26 C14 A B C D E F G H I J K L M N O P Q R S T U V W Y Z Model ML1C25 ML1C32 ML1C40 274 260 137 140 88 108 87 85.5 60 74 97 100 42.5 26 34 206 28 24 5.6 9 5.5 M5 x 0.8 8.5 M6 x 1 9.5 11 M8 x 1.25 322 306 161 160 108 131 101 99.5 64 92 118
For installation and removal, use an appropriate pair of pliers (Tool for installing a type C snap ring). 2.
Please place an order with cap type from the beginning.
H IDX-OM-V020 Chapter 7 Documents 7.3 Dimensions Port size Compressed air inlet Compressed air outlet Port size A B E D G F C P J Unit: mm M N O L K H Unit: mm Model Port Size A B C D E F G H J K L M [N] O P IDFA60 R1 307 745 605 161 405 681 71 330 704 355 126 94 46 12.5 IDFA70 R1-1/2 342 890 825 176 480 905 68 365 849 390 81 20 IDFA80 R2 438 957 863 169 480 958 219 78 100 11.0 463 916 485
They do not guarantee an actual fixed range (expect approximately 30% dispersion).
Note 3) K (High pressure) and Y (Low wattage) are not available. Electrical ently: L/ M plug connector only.
Set value IO-Link is an open communication interface technology between the sensor/actuator and the I/O terminal that is an international standard, IEC61131-9. *1 IODD File: IODD is an abbreviation of IO Device Description. This file is necessary for setting the device and connecting it to a master. Save the IODD file on the PC to be used to set the device prior to use.
(Effective for up to the number of set channels) Interrupting an operation via an external switch is possible using input signals.
In the case of obtaining an accurate flow rate, refer to front matter pages 1 to 6.
Confirm that this value is less than 1/20 of the effective torque. 20 x 9.8 x (m1 + m2) x H/1000 20 x 9.8 x (0.07 + 0.05) x 10/1000 = 0.24 Graph 3
Note) The -X126 model cannot be manufactured with an L plug connector for electrical entry. Therefore, use a grommet type or an M plug connector.
Screw-in Piping M5 X 0.8 Relieving port size 50 to 500mm/s Piston speed Mounting Basic, Axial foot, Front flange, Rear flange *Auto switch attachable Dimensions REC B/Basic H2 2-Rc(PT)P Width across flats B2 2-NN G G H1 Width across flats B1 Relieving port M5 X 0.8 Standard port I Relieving port 2-Eh8 D MM AL K A N N F lNA S+Stroke H F ZZ+Stroke (mm) A AL B1 B2 D E F G H H1 H2 I K MM N NA
VN Valve option Nil V Standard For vacuum, non-leak LVC LVA Select an option mark in page 17-3-14 by Applicable Fluids Check List for special fluids outside of the standard. LVH LVD Table (1) Port/Orifice Size Valve (Port size) Orifice size (No.)