ZSE30/ISE30 A switch output malfunction may occur. 12 SMC'S GLOBAL MANUFACTURING, DISTRIBUTION AND SERVICE NETWORK EUROPE SLOVENIA SMC Industrijska Avtomatika d.o.o. SPAIN/PORTUGAL SMC Espaa, S.A. SWEDEN SMC Pneumatics Sweden AB SWITZERLAND SMC Pneumatik AG. UK SMC Pneumatics (U.K.) Ltd. EUROPE AUSTRIA SMC Pneumatik GmbH CZECH SMC Industrial Automation CZ s.r.o.
Short on the load of the directional control driver indicates an error, but it may cause over current and damage the directional control driver. 2. Do not operate or conduct any settings with wet hands. An electric shock may result from wet hands. 3. When operating the manual switch, avoid making contact with the workpiece. Contact with the workpiece may cause injury. Caution 1.
Failure to do so may cause damage or malfunction.
If the load ratio exceeds 50%, this may cause problems such as failure of the lock to release, or damage to the lock unit. 5. Do not operate multiple cylinders in synchronization. Avoid applications in which two or more end lock cylinders are synchronized to move one workpiece, as one of the cylinder locks may not be able to release when required. 2.
The flatness of the mounting face may deteriorate, the guide's deviation range may increase and the sliding resistance may become greater. 3. Do not allow hands or fingers near the cylinder during its operation. Your fingers may be caught between the body and the plate. If you need to come near the cylinder during its operation, install a cover on the cylinder. 1.
Operation outside of this range may cause excessive impact, which may result in the damage to the device. Make sure to operate strictly within the allowable lateral load range to the plate. Operation outside of this range may result in shorter service life or damage to the device.
This may be shorter depending on the type of fluid and operating conditions, etc.
Failure to do so may cause damage or malfunction.
(Assuming approximately 30% dispersion) There may be the case to change substantially depending on an ambient environment.
Injury may result. 2. Do not drop, bump, or apply excessive impact. Damage, equipment failure, or malfunction may occur. 7 EX245 Series Specic Product Precautions 2 Be sure to read this before handling the products.
A poppet may be pushed on to a seat by positive pressure, but lifted back off by vacuum, resulting in a leak. For this reason internal design may preclude ostensibly suitable valves from vacuum applications. Series VT Not Available In The USA BACKGROUND Many current pneumatic solenoid valves are a c t u a l l y o f s o l e n o i d p i l o t c o n s t r u c t i o n .
When a switch is tightened beyond the specified tightening torque, the mounting screws, mounting bracket, or switch may be damaged. On the other hand, tightening below the specified tightening torque may cause the installation screws to come loose during operation.
Otherwise malfunction may result. 2. Please do not scratch or gouge the sliding part of the finger. It may increase the sliding resistance or cause abrasion. 3. Use a speed controller, etc. to keep the operating speed of the finger within the proper range. Otherwise the life time may be adversely affected by inertia force of the attachment. 4.
The following procedures are an example of how a test may be performed. It is intended as an overview and not as an all inclusive description. 1) Rotate the adjustment wheel counterclockwise (DECR) completely to relieve spring force.
Cylinder bores are manufactured to precise tolerances, so that even a slight deformation may cause faulty operation. Moreover, scratches or gouges, etc., in the sliding part of the piston rod may cause malfunction. 4. Prevent the seizure of rotating parts.
Using a model without a back flow mechanism makes for inconsistent residual pressure release (i.e., residual pressure may or may not be released) depending upon the operating conditions. 2) Contact SMC if air will not be consumed in the system for a long period of time, or if the outlet side will be used with a sealed circuit and a balanced circuit, as this may cause the set pressure of the
The switch may be damaged if it is tightened above the tightening torque range. Also, if it is tightened below the tightening torque range, the connection thread section may become loose.
Any port may be pressurized, back,pressured. or plugged without affecting spoot action. ANSt symbot shows the vatve a6 a slngle inl6t as a single intl 4-way, but vatve may be us6d, wilhout modtfication, as a dual Inlel 4-way, a O-way, or a 2.way, by ptping and/or ptugging the appropriale ports. MOUNTING: Intended for sub.ptate or manitotd mounting. May be mounted In anv Dosi. lion.
If the pressure differential at each port exceeds the values in the table below, valve leakage may occur.
AD402-A Current model Double layer design Cracks may occur in a portion where the internal pressure is applied.