Do not connect black. Power supply/output connection lead wire Cable Specifications Pin no.
Do not use the auto drain valve in such environment.
Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water or steam, or where there is direct contact with same. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. Do not use in a location where radiated heat will be received from a heat source in the vicinity. 5.
Do not inadvertently move the guide adjusting unit. The guide is installed at the proper tightening torque. Do not loosen the mounting bolts of the guide. 2. Do not operate the magnetic rodless cylinder if the magnet couplings on the actuator are displaced.
Do not inadvertently move the guide adjusting unit. The guide is installed at the proper tightening torque. Do not loosen the mounting bolts of the guide. 2. Do not operate the magnetic rodless cylinder if the magnet couplings on the actuator are displaced.
S 24 M5 x 0.8 (Finger closing port) 42 8 3 4 3 MHY2-25D2 Opening/Closing direction through-hole type 4-5.5 (Hole for mounting attachment) 12 0.005 0.025 6 12 22.5 (Limted area for mounting attachment) Do not extend the attachment from limited area for mounting to avoid interference with the attachment or main body. 12-10-14 14 180 Angular Style Air Gripper Cam Style Series MHY2 Mounting
S 24 M5 x 0.8 (Finger closing port) 42 8 3 4 3 MHY2-25D2 Opening/Closing direction through-hole type 4-5.5 (Hole for mounting attachment) 12 0.005 0.025 6 12 22.5 (Limted area for mounting attachment) Do not extend the attachment from limited area for mounting to avoid interference with the attachment or main body. 12-10-14 14 180 Angular Style Air Gripper Cam Style Series MHY2 Mounting
12 19 23.5 B 13 15 14 19.5 A 14.5 12.5 19.5 24 B 13.5 15.5 14.5 20 B 7.5 9.5 8.5 14 B 10.5 12.5 11.5 17 B 7 9 8 13.5 20 25 32 40 Note) When setting an auto switch, be sure to check its operation before adjusting.
IEC 60204-1: Safety of machinery -Electrical equipment of Do not use in an explosive atmosphere. Do not expose to direct sunlight. Use a suitable protective cover. Do not install in a location subject to vibration or impact. Check the Maintenance of pneumatic systems should be performed only by qualified personnel.
However, do no rotate the cushion valve exceeding two turns, and do not rotate the speed controller valve exceeding four and half turns (40: maximum two turns). If 0.6 Nm or more of torque is applied, the valve may become loose and may jump out depending on the amount of air pressure. Cushion Adjustment The air cushion is built in on the head end for the CK1 series.
Note 14) For an actuator with lock, add the power consumption for the lock.
A B A 14 A B A B A 14 A B A 14 A B 3 2 A 14 U side D side D side U side 0 1 5 4 2 3 B 12 B 12 B 12 B 12 B 12 7 8 1 2 3 4 5 Valve stations EX600-ED4 1 set EX600-WEN1 1 set EX600-EU1 1 set SS5Y3-10S6WE72-05B-C6 (Type 10 5-station manifold base, Wireless EtherNet/IP) Negative common, M12 connector IN/OUT pin arrangement 1, I/O unit: 2 stations * SY3100-5U1 3 sets (2-position single part no
Refer to p.3.4-14. Auto Switch Mounting Bracket Part No.
Do not use two wire sensors.
If the products kinetic energy exceeds the allowable value, it could damage the product, and cause a hazard to humans and damage the machinery or equipment. (14) Do not stop or hold the product at midpoint by keeping air pressure in the product.
Do not Do not use in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. The product is not designed to be explosion proof. Do not Do not use the product for flammable or highly permeable fluids. Fire, explosion, breakage or corrosion can result. Do not Do not use the product in a place where static electricity is a problem.
Warning (1) Do not disassemble or repair the product.
Form w 1 Material e r Vacuum inlet Flat Type with Groove C2 Connection thread 04 20 12 1.2 M10 x 1 3 Width across flats 7 06 08 1.8 10 13 16 A12 30 18 M12 x 1 2 Width across flats 14 N S U F GN GS HS Pad diameter: 10 to 16 A10 ZP3 T UM B5 M5 0.8 Width across flats 14 D 5 E E B A Dimensions Per Vacuum Inlet: One-touch Fitting Model A B Fitting part min. hole size Fitting part no.
The latching solenoid option(with self holding mechanism)functions in the same manner as a 2 position double solenoid but uses only one solenoid to do the job.