0.01 wiring/Supply port right) IN Spacer Seal for additional station End plate L End plate R Y200-A ISA-7-B ISA-6-B ISA-7-A When a 2 port solenoid valve is connected to the right: ISA-6-A When 2 air catch sensors are connected or when a 2 port solenoid valve is connected to the left: Bracket ISA-4-A Straight, 5 m A pair consists 1 set.
If a directional switching valve (solenoid valve, mechanical valve, etc.) is mounted on the supply side of the regulator and repeatedly switched ON and OFF, wear of the nozzle/flapper section will be accelerated and a discrepancy in the setting value may occur. Therefore, avoid using a directional switching valve on the supply side.
AD17-A AD27-A AD37-A AD47-A Spacer Y100-A Y200-A Y300-A Y400-A Y500-A Y600-A Spacer with bracket Y100T-A Y200T-A Y300T-A Y400T-A Y500T-A Y600T-A Check valve 5 6 AKM2000-01-A (02)-A AKM3000-(01)-A 02-A AKM4000-(02)-A 03-A Pressure switch 6 IS10M-20-A IS10M-30-A IS10M-40-A IS10M-50-A IS10M-60-A T-spacer 5 6 Y110-M5-A Y210-01-A (02)-A Y310-(01)-A 02-A Y410-(02)-A 03-A Y510-(02)-A 03-A Y610
pilot port) 44 62 9 9 91 44 62 Station number 50.5 59 2-Rc 1/8 (External pilot port) R4.5 R4.5 50.5 9 9 U side entry (LU) U side D side D side U side n 15 X X n X 12 12 12 12 8 B 2 A 4 B 2 A 4 8 Manual override 7 B 2 A 4 SMC SMC SMC SMC SMC SMC SMC B 2 A 4 7 A B A B A B A B A B A A A B A B A B A B A B A A SMC SMC SMC SMC SMC SMC SMC B B B A A A A A A A B A B 2 A 4 6 B 2 A 4 6 B B A A A A
4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 2-One-touch fitting (X, PE ports) Applicable tube O.D.: 6 2n-One-touch fitting (A, B ports) Applicable tube O.D.: 4 6 (L4) L3 (3.2) 113.7 U Side D Side 3.1 8 36.3 43.7 5.5 (DIN rail dimension) 35 18 28.8 DIN rail holding screw Manual override In case of locking type, turn after pushing in.
A O OUT 2 I N 1 SMC A J A IN OUT H G M Parts list Material Note Description No.
Reduced maintenance costs The magnetic separator prevents mechanical problems caused by contaminants such as abrasive particles and greatly reduces maintenance costs. 55 x t20 100 x t30 FHMN-055 FHM-100 FHM-200 0.2 20 0.9 100 2.5 200 200 x 140 x t40 Note) For example, three FHM100 magnetic separator units would be sufficient for a 300-liter fluid storage tank.
It is an assembly of a piston and a gasket (KSYP-13).
lrlA |.25N/A r{/A.1 3 .35 t ( l{/A 13.9 or.
Therefore, air does not blow out to the outside. 1 Soft Start-up Valve AV2000-A/3000-A/4000-A/5000-A Series Variations Series C [dm3/(sbar)] Port size Voltage Electrical entry Option 1(P), 2(A) 3(R) AV2000-A 9.2 1/4 1/4 100 VAC 200 VAC 110 VAC 220 VAC 24 VDC 12 VDC AV3000-A 13.1 3/8 3/8 Bracket Pressure gauge Silencer (Built-in) Grommet DIN terminal AV4000-A 19.2 1/2 1/2 AV5000-A 34.8
For a facility having a large installation area (that can vent the air naturally): Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level.
MA a CHM A MA a Cushion adjustment screw Air release R (max.)
Make sure to connect a speed controller to the cylinder and adjust it so that the cylinder speed will be within a range of 50 to 200 mm/s. If a clamp arm other than the available option is used, make sure to select an appropriate arm after calculating the inertial moment of the arm.
top ported R 3 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 39.5 (58.1) 62.1 41.7 25.7 2 B 2 B 2 B 2 B 2 B 2 B 2 B 2 B 20.9 P 1 P=17.5 63.3 44.5 7.5 One-touch fitting [4(A), 2(B) port] Applicable tubing O.D.: 4 : 6 : 8 L n Formula: L1 = 17.5n + 52, L2 = 17.5n + 74.5 n: Stations (Max. 16 stations) Dimensions 16 332 354.5 375 385.5 15 314.5 337 362.5 373 14 297 319.5 350 360.5 13 279.5 302 325 335.5 12
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
watch maker's screwdriver with a grip diameter of 5 to 6mm.
If there is a risk of contact, provide safety measures such as a cover or a system that uses sensors that will activate an emergency stop before contact is made. 2. Use a balance circuit in which lurching of the piston is taken into consideration.
When using a single/double knuckle joint together with a rod end nut, the A and H dimensions should be extended.
watch maker's screwdriver with a grip diameter of 5 to 6mm.
When using a single/double knuckle joint together with a rod end nut, the A and H dimensions should be extended.