Applicable Auto Switch Model 100 14 63 13 12 7.5 50 11 80 13 40 11 15 16 8.5 20 9.5 9 10 8.5 25 9.5 9 10 32 11 11 Note) qIn the case operation load is an inductive load.
13 16 16 20 20 11 11 10.5 11.5 12.5 14 12 16.5 26 30 36 42 48 54 64 78 8 10 12 16 20 20 25 25 6 8 10 12 16 16 20 20 M4 x 0.7 90 94 109 109.5 135.5 142 155 160 13 15 18 21 24 27 32 39 M4 M4 M5 M5 M6 M6 M8 M10 7 7 9 9 9 9 10 10 5 5 6 6 10 10 12 12 42 46 53 53.5 59.5 66 72 77 19 19 30 30 38 38 60 60 8 8 10 10 12 12 16 16 51 58 68 82 100 108 139 153 8 8 10 10 12 12 16 16 58 64 83 93 112 120
A grease pack (10 g) is included. If an additional grease pack is needed, order with the following part number.
Note 10) A reference value for correcting an error in reciprocal operation. Switch and Acceleration Note) Table 2 Switch no. Acceleration [mm/s2] 0 250 1 500 2 1000 3 1500 4 2000 5 2500 6 3000 7 4000 8 5000 9 6000 10 7500 11 10 12 12500 13 15000 14 17500 15 20 Note) The factory default setting for the switch is No.0.
EXW1 EXW1 Up to 100 m V.1.0 / V.2.0 Available *1 EXW1 EXW1+EX600 *2 V.1.0 Not available EXW1 EX600 Up to 10 m V.1.0 Not available EX600 EXW1 Up to 10 m V.1.0 Not available Available *3 EX600 EXW1+EX600 Up to 10 m V.1.0 Not available Available *3 EX600 EX600 Up to 10 m V.1.0 Not available Available *1 Available in protocol V.2.0. *2 Up to 100 m between an EXW1-series Base and Remote, and up
*10 *10 *10 *10 *10 *7 For pipe thread type: NPT.
As an example, for a travel of 100 (mm) Travel distance of the actuator per 1 pulse = 0.001 (mm) *1 100 (mm)/0.001 (mm) = 10 (pulse) If the stroke end signals (LSP, LSN) are not turned ON, an alarm may occur.
8 (left side) One-touch fitting 10 (left side) Mixed 02R 03R 02L 03L 02Y 03Y C6R C8R C10R C6L C8L C10L Control equipment Symbol Nil A AP M MP F G C E Air filter with auto drain 10 stations 10 Air filter with manual drain Note) When equipped with control unit, one or two stations are used for mounting.
parts. 359 5 Port Solenoid Valve 10-SYJ7000 Mix Installation of the 10-SYJ700 and the 10-SYJ7000 Valves on the Same Manifold Use of an adapter plate makes it possible to mount the 10-SYJ700 on the 10-SYJ7000 manifold bases.
Connector wiring diagram (mixed wiring) Connector type manifold 6 A 4 A 3 A 1 A 5 B 2 B Output 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 1 2 3 4 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 The use of multi-pin connectors to replace wiring inside manifold blocks provides flexibility when adding stations or changing
10 10 14 14 15 17 17 21 21 51 58 58 71 72 6 7 7 10 10 14 18 18 22 26 30 35 40 48 58 M14 x 1.5 27 30 31 37 40 1/4 3/8 3/8 1/2 1/2 10 12 16 20 25 16 19 23 28 36 30 35 35 40 40 27 32 32 37 37 60 70 85 102 116 22 27 27 32 41 44 52 64 78 92 10 12 16 20 25 15 18 25 8 11 11 13 16 M8 x 1.25 M18 x 1.5 M10 x 1.25 M18 x 1.5 M12 x 1.75 M22 x 1.5 31.5 M12 x 1.75 M26 x 1.5 35.5 6-8-36 37 Series CA2Q Air
N-04 N-06 L-04 L-06 S-04 S-06 LL-04 LL-06 4 6 N-08 8 N-10 10 N-12 12 4 6 L-08 8 L-10 10 L-12 12 4 6 S-08 8 S-10 10 S-12 12 4 6 LL-08 8 LL-10 10 LL-12 12 Precautions Be sure to read before handling.
level: 1 Air flow level: 1 10 10 10 10 Air flow level: 10 5 Air flow level: 10 5 Air flow level: 10 Air flow level: 10 5 5 Air flow level: 10 Air flow level: 10 5 5 0 0 0 200 400 600 800 1000 1200 1400 1600 0 200 400 600 800 1000 1200 1400 1600 0 0 0 0 Installation distance [mm] 0 200 400 600 800 1000 1200 1400 1600 0 200 400 600 800 1000 1200 1400 1600 Installation distance [mm] 0 200 400
(Supply pressure 0.3 MPa) External air inlet Compressed air External air inlet Yes None Reduced by 50% Air consumption flow rate L/min (ANR) 10 10 Ionized air Discharge time sec 2.5 2.5 5 Compressed air Improved 6 times Ionized air flow velocity m/s 0.4 At 300 mm distance External air inlet External air Neutralizing static electricity from an electric substrate Neutralizing static electricity
An error code is returned if an instruction code outside the range set in parameter No.
Select zero cut-off setting Press the UP or DOWN button to select the value of zero cut-off. : The display above is an example when 10 L range and unit selection function are [L/min] selected. : When the actual flow is smaller than the displayed value in the upper line, zero will be displayed. Example: 10 L range Press the SET button to set. Return to function selection mode.
Laser output power 3 [kW], conversion efficiency 30% The oscillators power consumption is, 3 [kW] 0.3 = 10 [kW] The cooling capacity required for the oscillator is, 10 [kW] 3 [kW] = 7 [kW] Considering a safety factor of 20%, 7 [kW] x 1.2 = 8.4 [kW] W Efficiency Q = P = In this example, using an efficiency of 0.7: 5.1 0.7 = = 7.3 [kW] Q: Heat generation amount Cooling capacity = Considering
Select the proper size of cable according to an actual condition.
Blow Velocity Distribution (Supply Pressure: 0.3 MPa) qEnergy saving static neutralization nozzle IZN10E-01 wHigh flow rate nozzle IZN10E-02 0 0 100 100 Distance [mm] Distance [mm] 200 200 4 m/s 14 m/s 300 300 11 m/s 3 m/s 400 400 8 m/s 2 m/s 500 30 30 20 10 0 10 20 500 30 30 20 10 0 10 20 Distance (Horizontal) [mm] Distance (Horizontal) [mm] 8 IZN10E Series Flow Rate Characteristics qEnergy
Damage may occur if an excessive load is applied to the switch. 10. Be sure to allow straight pipe length that is minimum 8 times the port size upstream and downstream of the switch piping.