LV50-OMQ0002 Do not Do not use the product in a place where static electricity is a problem. Otherwise failure or malfunction of the system can result. Do not If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system. Check the product for proper operation. Otherwise malfunction can result, causing an accident.
Vibration resistance: No malfunction occurred in a test ranging between 45 to 2000 Hz. The test was performed in both an axial direction and a perpendicular direction to the lead screw.
Cautions for use in an interlock circuit. When an auto switch is used for an interlock signal requiring high reliability, devise a double interlock system to avoid trouble by providing a mechanical protection function, or by also using another switch (sensor) together with the auto switch. Also perform periodic maintenance and confirm proper operation. 9.
Air cushion is installed to prevent the impact which occurs as the piston is stopped at the stroke end with a large moment. Air cushion is not applied for slow piston operation around the stroke end. A range of the weights a and speeds that an air cushion can absorb is within the limits shown in the graph, "Air cushion absorbing capacity".
bracket assembly with a part number shown in the table left below is included as an accessory.
Common exhaust 5.1-3 VEX1 Flow Characteristics VEX110, 120 VEX190 A port pressure MPa P Port pressure 1.0 MPa A port pressure MPa P Port pressure 1.0 MPa VEX130 Setting Pressure Characteristics A port pressure MPa P Port pressure 1.0 MPa A port pressure is set in accordance with pilot pressure VEX150 A port pressure MPa P Port pressure 1.0 MPa VEX AN AMC External Pilot Piping VEX170 A port
If the cable is bent in an acute angle or load is applied to the cable successively, it may cause a malfunction, broken wire or fire. 2. Mount this product on a plane surface. Mounting on an uneven surface will apply excess force to the frame or case, which leads to damage or failure. Do not drop the product or subject it to a strong impact. This may cause an injury or accident. 3.
Provides a stable supply of dry air even under high demand conditions with an inlet air temperature of 60C. IDU3D to 6D: 60C IDU8D to 37C1: 55C IDU55C, 75C: 50C Series IDF Can accommodate an inlet air temperature of 40C System efficiency is improved by using a high performance heat exchanger.
Specifications CCT40 Effective oil level stroke Operating pressure 0 to 0.7 MPa Proof pressure 1.05 MPa Because the CCT40 is a converter for an actuator with a small capacity, it cannot be made into an air-hydro unit.
It can be used alone as a tank. The pressure vessel law is different from country to country, so as an air tank suitable to a country needs to be confirmed.
CCT40 Effective oil level stroke Specifications 0 to 0.7MPa Operating pressure Because the CCT40 is a converter for an actuator with a small capacity, it cannot be made into an air-hydro unit.
Instead, use an individual CC valve unit or a speed controller (AS2000, AS3000, AS4000, etc.) through a pipe connection.
When mounting an auto switch (3) Tube top mounting (When mounting an auto switch into the groove from the top before holding the product) (When mounting an auto switch into the groove from the top after installation) Auto Switch Proper Mounting Position [mm] Auto switch model Bore size D-M9, D-M9W D-M9V, D-M9WV D-M9A D-M9AV A B W A B W A B W A B W 12 6.2 6.2 3.8 6.2 6.2 1.8 6.2 6.2 5.8
A cabtire cable with an O.D. 6 to 12 mm is applicable. Tighten each part with an appropriate tightening torque shown below.
To operate a relay as a load, use the relay shown in the table below or the equivalent, in order to extend the life of the switch. qWhen handling the product, do not drop an object on it, gouge it, or apply an excessive impact on it. wDo not operate it in an area in which a large amount of magnetism is present.
SMC'S AC se^/o etectric actuatoF are closed loop if an applicaion has ifregular or unpredictable foads, a closed]oop system may be desirabte over an open-loop one. see also closed Laop conid System, Open Loq Control Systetn. Micrqsiep a regular increments srnaller than a half step. Micro-stepFing is a funclion of the ddverj this feature.
Plug-in Unit VQ5000 Series Bottom ported drawing With connector on U side (FU) SV 106 61 SYJ 83.5 9 9 55.5 M5 x 0.8 Ground screw SZ 1/2" 4(A), 2(B) port 34.5 VF n U side X 12 VP4 B 2 A 4 6 VQ 1/2 B A B 2 A 4 VQ 4/5 VQ 4/5 5 SMC SMC SMC SMC SMC B A VQC 1/2 B 2 A 4 4 VQC 4/5 B A P = 41 L1 L2 B 2 A 4 VQZ 3 B A SQ B 2 A 4 2 B A VFS B 2 A 4 VFR 1 B A VQ7 58.5 34.5 46 68.5 X 12 Stations 1/8" External
Draining If this product is used with a large amount of drainage accumulated in the filter, mist seperator, or the tank, the drainage could flow out, leading to equipment malfunction. Therefore, drain the system once a day. If it is equipped with an auto-drain, check its operation once a day.
When an offset load is expected, provide a suitable mechanism such as a floating joint. 2) Use clean air (atmospheric pressure dew point temperature -10C or less). Use of a series AM mist separator (filtration rating of 0.3m or less), or series AM + AMD (filtration rating of 0.01m or less) is recommended.
A-q A-w A-e A-r A-t A-y A-u A-!1 A-y A-u A-!2 A-!