MB Cylinder (150C) -XB6 5 2 As it uses a powerful scraper for the wiper ring, this cylinder is suitable for use in an area that is dusty, or in an environment in which mud splashes on the cylinder, such as when operating casting equipment, construction equipment, or an industrial vehicle.
Since terminal numbers are not indicated on the flat cable, use the triangle mark as a reference when wiring. 8 Cassette Type Manifold Series SZ3000 Manifold Electrical Wiring 60PG Flat cable type (20 pins) Without power supply terminals With power supply terminals Positive common Negative common Common 20 20 20 Pos. pin (common) Pos. pin 19 19 19 SOL.B 18 18 Neg. pin Neg. pin (common)
LZ LC3F2 T4 = 0.2 [s] Calculation example) T1 to T4 can be calculated as follows. 200 T1 = V/a1 = 200/3000 = 0.067 [s], T3 = V/a2 = 200/3000 = 0.067 [s] 160 Overhang: L1 [mm] T2 = = = 0.033 [s] L 0.5 V (T1 + T3) V 20 0.5 200 (0.067 + 0.067) 200 120 T4 = 0.2 [s] 80 Therefore, the cycle time can be obtained as follows.
When an impact, such as water hammer, etc., caused by the rapid pressure fluctuation is applied, the solenoid valve may be damaged. Give an attention to it. 2. Fluid quality
(The motor rotates in the reverse direction if the table hits an obstacle such as the end stop damper.) Take the motor phase detection step into consideration for the installation and operation of this electric actuator. 20 No.JXC-OMW1019-A Caution (1) Keep the controller and product combined as delivered for use. The product is set in parameters for shipment.
Full scale ranges as low as 1.5 psi pressure and 3" Hg vacuum are available. Settings as low as 1" WC are easily maintained with both. Both units will also accept a pilot input, allowing pneumatic control of the output setting (see schematics).
x 1.5 C B-series M6 x 1.0 M8 x 1.25 40 145 115 75 60 E 31.5 30 20 24 M30 x 1.5 dH10 L L M6 x 1.0 M8 x 1.25 40 145 115 75 60 31.5 30 20 24 M39 x 1.5 M8 x 1.25 M10 x 1.5 50 185 145 95 80 40 40 25 26 M48 x 1.5 H +0.4 +0.1 D M5 x 0.8 M6 x 1.0 25 76 60 41 32 16 16 12.5 20 M16 x 1.5 M5 x 0.8 M6 x 1.0 31.5 90 70 50 40 20 20 16 20 M20 x 1.5 B J M6 x 1.0 M8 x 1.25 40 145 115 75 60 31.5 30 20 24 C-series
Accessories Nil B None (standard) With bracket Note) When symbol B is indicated, a bracket assembly with a part number shown in the table below is included as an accessory.
Never remove the plugs as this will cause malfunction. 20 30 70 100 200 50 10 Size Tightening torque N . m 1.67 62.8 3.14 23.5 10.8 2. Never rotate the bottom screw of the shock absorber. (It is not an adjustment screw.) This may cause oil leakage.
1 Single Axis Electric Actuator High Rigidity Direct Acting Guide Series LJ1H Series LJ1H LJ1 LG1 LC1 LX LC6D/LC6C Switches Lead screw lead mm Mounting orientation Series Page Model Motor type Guide type Ground ball screw Rolled ball screw Slide screw 12 10 20 12 10 20 20 20 40 LJ1H10 LJ1H20 LJ1H30 LJ1H10 LJ1H20 LJ1H30 LJ1H10 LJ1H20 LJ1H30 LJ1H10 LJ1H20 LJ1H30 2 Horizontal 8 25 25 18 Standard
Manually Unlocking Holding the Unlocked State (20 through 32) Warning Caution 1. Do not perform unlocking while an external force such as a load or spring force is being applied. This is very dangerous because the cylinder will move suddenly.
Manually Unlocking Holding the Unlocked State (20 through 32) Warning Caution 1. Do not perform unlocking while an external force such as a load or spring force is being applied. This is very dangerous because the cylinder will move suddenly.
Perform inspections on a regular basis as necessary, such as at the beginning of an operation, to make sure that the mechanical valve operates properly. Failure to observe this precaution could lead to unsafe operation, such as unintended operation or malfunction.
(n 2) (n = 4, 6) D-M9lWV D-M9lAV 10 15 15 + 15 (n 2) (n = 4, 6) D-F7lW D-J79W D-F7BA 10 15 15 + 20 (n 2) (n = 4, 6) D-M9lW 15 15 15 + 15 (n 2) (n = 4, 6) D-M9lA 15 20 20 + 15 (n 2) (n = 4, 6) *1 Auto switch mounting (With the stroke range within the below, an adjustment is required as shown in the chart below).
[As Mp and My does not arise, examination is not needed.] Mr = 0.2 x 9.8 (20 + 6.8)/1000 = 0.053 Ma = Mmax Find the allowable static moment Ma (Nm).
NSR 18 Piston seal NBR 20 Tube gasket NSA ,-External dimensions are the same as the CS2 standard type. Refer to pages 7 to 10.
If the chewed portion of the tubing is used as is, this can case trouble such as air leakage or difficulty in removing the tubing. 2. Tightening of M3 and M5 screws 1) M3 1. After tightening by hand, the barb fitting type should be tightened by an additional 1/4 rotation using an appropriate wrench. 2.
bolt Push Push Auto operation Auto operation Possible to operate by using the same signals as those for a solenoid valve (with a PLC) Possible to operate by using the same signals as those for a solenoid valve (with a PLC) Having both the operationability of an air cylinder and the speed controllability of an electric actuator New actuator concept Machine difference 3 3 Both end position