HRX-OM-I051 Use assistance to carry object over 20 kg. Check that all parts and screws are returned to the pre-work conditions at the end of work. Do not work when intoxicated or feeling ill. Accidents may occur if disregarded.
Do not use the valves in an atmosphere having corrosive gases, chemicals, salt water, water, steam, or where there is direct contact with any of these. 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5.
(mm) Bore size (mm) WA WB WH W ZZ 20 22 16 23 30 118 25 22 16 25 30 123 32 22 16 28.5 25 125 40 22 16 33 20 143 50 25 18 40.5 20 167 63 25 18 47.5 20 167 80 30 22 60.5 20 201 100 31 22 71 20 202 10 Series CG5-S Dimensions R V Axial foot type (L)/CG5LNS S + Stroke H GA GB Width across flats B1 2P H1 D B LH I AL A K KA MM Width across flats NA LT M X Y X Y 8-J 4-LD C 0.1 LS + Stroke LX LZ ZZ
Do not use in the place creating magnetic field to prevent the malfunction of the actuator. Do not use in the environment subject to temperature cycle. Do not use where close to surge generating source. Do not short the load. Short of the load of the controller is indicated as error, but it may cause over current and break the actuator.
to 350 Note 4) Basic Compact Basic Compact Basic Compact Basic Compact Basic Compact Horizontal Max. work load [lb] Note 2) Note 3) Vertical Actuator specifications Electric specifications 20 to 300 Note 4) Horizontal 20 to 350 Note 4) Speed [mm/s] Note 3) Note 6) 20 to 300 Note 4) 20 to 300 Note 4) Vertical 20 20 to 300 Note 4) Pushing speed [mm/s] Note 5) 20 Acceleration/Deceleration
For example, changing from F Kit (D-sub connector) to S Kit (serial transmission) is achieved by simply changing the kit piece. 19 20 19 20 19 20 19 20 19 20 19 20 19 20 19 20 COM Station 1 Double wiring Station 2 Single wiring Station 3 Double wiring Station 4 Single wiring (Refer to the connector wiring diagram) Printed circuit board patterns between connectors are shifted at every station
Do not apply excessive lateral load to the piston rod.
Do not remove the panels except for the cases permitted in this manual. Do not remove the panels during operation. Use assistance to carry object over 20 kg.
20 50 98 70 84 44.5 11 6.4 117.5 16 3.3 316 280 46 20 196 11 20 98 50 70 44.5 84 13 319 11 6.4 117.5 3.3 Note 1) For AC20 only, the position of the pressure gauge is above the center of the piping.
MPa 24 SMC 32.5 20 0.5 0.1 0.3 24 56 17 17 5.
MPa 24 SMC 32.5 20 0.5 0.1 0.3 24 56 17 17 5.
Do not use the product in an area where dust, powder 2. Do not operate the product beyond the specifications. dust, water, chemicals or oil is in the air. It will cause failure or malfunction. Otherwise, a fire, malfunction or actuator damage can result. Please check the specifications before use. 11. Do not use the product in an area where a magnetic 3.
For detecting fine pressure, warm up the product for 20 to 30 minutes. Check if the product satisfies the specified accuracy in 20 minutes after supplying power.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Refer to pages 6-20-3 to 6-20-6 for Safety Instructions and Actuator Precautions. Operating Precautions (mm) Comparison of the Full Length Dimension (Versus standard type) Warning 1. Do not rotate the cover.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not use in environments where there is a danger of corrosion. 2. Do not use in direct sunlight. 3. Do not operate in a location subject to vibration or impact. 4. When using auto switches, do not operate in an environment with strong magnetic fields. 5. Grease base oil can decrease depending on external environment and operating conditions.