, CLA/CLA2 TIE-ROD CYLINDER, P1, 63MM CLA PART, .00000 lb
P1, 63MM CQ2 PART, 1.21000 lb
CYL, P1, 63MM CY3B PART, 1.39084 lb
Solid State Vacuum Regulator Vs: Power supply 24VDC 12 to 15VDC One of the preset pressures P1 through P4 is selected by the ON/OFF combination of S1 and S2. S1 S2 Preset pressure OFF OFF P1 ON OFF P2 OFF ON P3 ON ON P4 For safety reasons, it is recommended that one of the preset pressures be set to 0MPa.
Pressure Momentary change P1 P2 Set value Anti-chattering function Devices such as large bore cylinders and high-flow vacuum ejectors consume a large volume of air when they operate, and this may cause a momentary drop in the primary pressure.
Mist generation pressure differential (MPa) IC EX: How to obtain the mist generating pressure differential if the flow rate obtaine in 1. above is 35 m3/min and the line pressure (inlet pressure P1) is 0.7 MPa: Extend horizontally from the point at which the flow rate is 35 m3/min to obtain the point that intersects with P1 = 0.7 MPa.
Step 20 Step 5 Analog output 4-20 mA 0-10 VDC P4 Set pressure P3 PPA P2 AL P1 0 1023 Digital input data Time Digital signal Digital signal Analog signal Analog signal Analog signal Analog signal Controller Actuator Electro-pneumatic regulator Actuator Electro-pneumatic regulator Controller PLC PWR PWR ERR ERR 1bit 2 bit . . . . 10 bit 010 VDC 420 mA 010 VDC 420 mA Series ITV Series ITV Series
Primary pressure normal Set value P1 P2 Time ON Switch output 1, 2 OFF Time [ ] Switch output response time when auto shift is input. 5 ms or more 10 ms or less Hi Auto shift input Lo 3 types of piping Different piping methods are possible to accommodate the installation location.
Vacuum pressure: P1 Conversely, the size of the ejector or the size of the switching valve of the vacuum pump system can be obtained from the adsorption response time.
Q=14.2Cv 10.2 P l/min G Formula based on effective area (Smm) Q=0.8S 10.2P l/min G Other : Flow rate (l/min) : Pressure differential (P1 P2) : Upstream pressure (MPa) : Downstream pressure (MPa) : Effective area (mm) : Cv factor : Fluid specific gravity (water = 1) Q P P1 P2 S Cv G 1. Materials FKM: Fluoro rubber Trade names: Viton, Dai-el, etc. 2.
(Including the mounted valves. ) 1.10-148 Manifold optionsSV5Q11OP, #1 to #3 VQ 1000/2000 Plug-in Unit Base Mounted EXH block base assembly VVQ1000-19A-(C3, C4, C6, M5) F P L Manifold block ass'y Electrical entry F1 F2 F3 P1 P2 P3 L0 For F kit (2 to 12 stations)/Double wiring For F kit (13 to 24 stations)/Double wiring For F kit (2 to 24 stations)/Single wiring For P, G, T, S kit (2 to 12
Effective area (Cv) (1) SYJ 0.8MPa 0.15MPa 5 to 50C 2.7mm2 (0.15) 180 c.p.m SUP side pressure (P1) To CYL port SX Note 1) As per JISB8375-1981 (Supply pressure: 0.5MPa) VK Max. operating frequency VZ Dimensions 21.5 (5) Manifold 18 VF Valve 29 10.5 2n-C4, C6 C4: One-touch fitting ass'y for 4 C6: One-touch fitting ass'y for 6 VFR 2n-C4, C6 C6: One-touch fitting ass'y for 4 C8: One-touch fitting
Item Classification pD(Torrcm) /D (Knudsen number) >0.5 <0.01 Viscous flow 0.5 to 0.015 0.01 to 0.3 Intermediate flow <0.015 >0.3 Molecular flow 8 Exhaust time (low/medium vacuum) 4 5 1 2 3 4 1 2 3 The time (gt) required to exhaust a chamber at low vacuum with volume V (l), from pressure P1 to P2, using a pump with pumping speed S (l/sec) is gt=2.3(V/S)log(P1/P2).
(the condition of P1 and Q1) 3. If the suction port is opened completely, the suction flow rate increases to the maximum (Qmax), while the vacuum pressure then drops almost to 0 (atmospheric pressure). When adsorbing work pieces which are permeable or subject to leakage, etc., caution is required as the vacuum pressure will not be very high.
Pmax P1 Vacuum pressure Qmax Q1 Suction flow rate 13-6-4
Vacuum ejector series ZA is compact and lightweight, making it ideal for pick and place operations, and suitable to all industries. Due to the compact design of the ZA, it is possible to install on moving parts. The shortened tube length to pad improves response time. The ZA is available as a single unit or manifold type, with or without pressure sensors and suction filters. Compact vacuum
This is a legacy product. Please contact us for the latest version.sales@ocaire.com, VACUUM EJECTOR, COMPACT, VACUUM SERIES, ZA COMPACT VACUUM EJECTOR, BG, ZA NOZZLE SIZE 0.5, .36219 lb
Vacuum ejector series ZA is compact and lightweight, making it ideal for pick and place operations, and suitable to all industries. Due to the compact design of the ZA, it is possible to install on moving parts. The shortened tube length to pad improves response time. The ZA is available as a single unit or manifold type, with or without pressure sensors and suction filters. Compact vacuum
Vacuum ejector series ZA is compact and lightweight, making it ideal for pick and place operations, and suitable to all industries. Due to the compact design of the ZA, it is possible to install on moving parts. The shortened tube length to pad improves response time. The ZA is available as a single unit or manifold type, with or without pressure sensors and suction filters. Compact vacuum
This is a legacy product. Please contact us for the latest version.sales@ocaire.com, VACUUM EJECTOR, COMPACT, VACUUM SERIES, ZA COMPACT VACUUM EJECTOR, BG, ZA NOZZLE SIZE 0.5, .32066 lb