SMC Corporation of America
Elite Part Number Search
Search Results "AFD20-N02C-CZ-A-X2141"

SPR3: Max. 1.0 A SPR2: Max. 2.0 A SPR4: Max. 1.0 A SPR5: Max. 2.0 A SPR7: Max. 1.0 A SPR6: Max. 2.0 A SPR8: Max. 1.0 A SDN1: Max. 2.0 A SDN3: Max. 1.0 A SDN2: Max. 2.0 A SDN4: Max. 1.0 A SMJ1: Max. 2.0 A SMJ3: Max. 1.0 A SMJ2: Max. 2.0 A SMJ4: Max. 1.0 A Supplied current IP67 IP40 IP67 14 to 122F (10 to 50C) 35 to 85%RH (No condensation) 500 VAC for 1 minute between terminals and housing

valve (A) (A) 4 (B) 2 (A) 4 (B) 2 Note) A 1 5 (R1) 3 (R2) 1 (P) 3 (R2) 5 (R1) 1 (P) N.C.

P P For the release valve, select a 2/3 port valve with a low vacuum specification. Also, use a needle valve to regulate the release flow rate. During the adsorption and transfer of a workpiece, verification of the vacuum switch is recommended. In addition, visually verify the vacuum gauge when handling a heavy or a hazardous item.

P P For the release valve, select a 2/3 port valve with a low vacuum specification. Also, use a needle valve to regulate the release flow rate. During the adsorption and transfer of a workpiece, verification of the vacuum switch is recommended. In addition, visually verify the vacuum gauge when handling a heavy or a hazardous item.

P P For the release valve, select a 2/3 port valve with a low vacuum specification. Also, use a needle valve to regulate the release flow rate. During the adsorption and transfer of a workpiece, verification of the vacuum switch is recommended. In addition, visually verify the vacuum gauge when handling a heavy or a hazardous item.

Note 4) Since this is a special product, a manifold part number is not specified.

SUP block plate VVQ2000-16A EXH block plate VVQ2000-19A Port plug Note 1) A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B C4 (N3) With 4 (5/32") One-touch fitting Side port Cylinder port sizes Fill out in case of mixed sizes (CM/LM/NM).

Operating principle A + A' A' A Piston seal A' A' R H R H When the piston is retracting, air is exhausted through both A and A' until piston seal H passes air passage A. After piston seal H has passed air passage A, air is exhausted only through A'. The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved.

KK KK EA MM MM B B E/2 4-NT ND Deep SN + Stroke (A + B) Stroke B Stroke A G C A TN C G A E XT XT LD + Stroke (A + B) WF WF ZZ + Stroke (A + B) (in) ZZ PC KK Y R XT G A LD Bore (in) DD C NT ND AA EA D B MM WF P K E SN TN EE 9.44 1.30 7/16-20 1.71 1.43 1 15/16 1.26 3/4 7.44 150 (1.5") 1/4-28 3/8 1/4-20 9/32 2.02 0.3 9/16 1 1/8 5/8 1 2.36 9/32 2 5.56 5/8 3/8 9.52 1.30 7/16-20 1.71 1.84 1 15

Recommended pneumatic circuit for the CKQG/P series The following is an example of a basic meter-out control circuit for operating a cylinder using an air filter, a regulator, a solenoid valve and a speed controller. 7) It is possible to use the pneumatic circuit shown below. However, unlock the cylinder before operating.

flow rate of 14.1 scfm [400 L/min] (ANR) is P1 29 psi (0.2 MPa) for a 4 orifice and P1 84 psi (0.58 MP)a for a 3 orifice.

B A HS 056 HS B A B A 075, 106 HS B A B A 150, 200, 250 Note 1) Figures in the table below are references for auto switch mounting positions in the stroke end detection.

Mineral oil A A A C A A 18 Sodium hypochlorite (2%, Room temperature) A C D A D B 19 Sodium chloride A A A A B 20 Carbon dioxide A A A A A A 21 Natural gas A A A A A A 22 Boric acid A B D A A B 23 Unless noted otherwise, the solution concentration is in a saturated state.

Regarding a vacuum switch valve and a vacuum release valve If a non-vacuum valve is installed in the middle of piping system having a vacuum, the vacuum condition will not be maintained. Use a valve designed for use under vacuum condition. 10.

Although a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if a surge is applied repeatedly. When directly driving a load that generates surge, such as a relay or solenoid valve, use a switch with a built-in surge absorbing element. 8.

B A HS HS B A B A 075, 106 HS B A B A 150, 200, 250, 300, 400 Note) Figures in the table below are references for auto switch mounting positions in the stroke end detection.

When a load, such as a relay or solenoid valve, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.

Mineral oil A C A A A A 18 Sodium hypochlorite (2%, Room temperature) A C A D D B 19 Sodium chloride A A A A B 20 Carbon dioxide A A A A A A 21 Natural gas A A A A A A 22 Boric acid A B A D A B 23 Unless noted otherwise, the solution concentration is in a saturated state.

A vacuum pad is a consumable part, so it is warranted for a year after it is delivered. Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the deterioration of rubber material are not covered by the limited warranty.