Possible to transfer a workpiece at low-speed. The rotation angle can be adjusted between 90 and 190. n io r a at n t g o Rotation starting point e R End of rotation DL L R B B L e o g t B a n ti a o r n n o r a ti n a g t Rotation starting point End of rotation o A A e Operating size 20 30 40 Operating size 20 30 40 R A Lmax 15 18 24 27 31.5 Size 10 15 20 30 40 Rotation starting point End of rotation Lmax 24 27 31.5 Lmax 24 27 31.5 Size
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Seal guide B Slide plate Spacer 21 22 Side seal unit MYMK-16-A MYMK-16-A MYMK-25-A MYMK-25-A MYMK-25-A 23 24 Hexagon socket head cap screw Chromated Chromium molybdenum steel 25 Replacement Parts: Seal Kit 20 40 50 25 32 63 16 No.
26 B 26 7 23 A B 11.5 Hs Hs 8.5 D-A7H D-A80H 1 10.2 7 22 A B D-C73C D-C80C A 36.7 B 16 Hs Hs 8.5 10 13.3 13.3 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com D-A73C D-A80C B 24 A Hs 18.6 B 16 A 29 D-H7 D-H7W D-H7BAL D-H7NF Hs 8.5 1 7 23.5 A B D-A79W 14 Hs A 38.2 B
x Depth 580 HRSE018-A-23 HRSE024-A-23 HRSE012-A-23-T 48 Height 790 x Width 470 x Depth 580 HRSE018-A-23-T HRSE024-A-23-T IDH Selection Warning 1.
Therefore, internal parts of a cylinder other than rod seal are not replaceable. 2. Use caution to the popping of a retaining ring. When replacing rod seals and removing and mounting a retaining ring, use a proper tool (Retaining ring plier: Tool for installing a type C retaining ring).
Table 3.8-2 RTU mode message frame Address c)Function d)Data e)Checksum a)Start b)Device (CRC) f)End T1-T2-T3-T4 XX XX XX XX XX XX T1-T2-T3-T4 a) Start In Modbus RTU mode, message frames are separated by a silent interval (noncommunication time).
Seal guide B Slide plate Spacer Hexagon socket head cap screw MYMK-16-A MYMK-16-A MYMK-25-A MYMK-25-A MYMK-25-A Side seal unit Nickel plated Seal List No. !
L R O D T H R E A D X A O P T I O N Thread Form Code M .
A B High precision type Basic type Port location Nil E Side ported Front ported Size 1 2 3 7 A With adjustment bolt Dimensions Clean series products do not have a hollow axis.
[Check valve] A check valve is a safety device intended to prevent reverse flow. The AP 64 is a unique design with only one moving part in the gas stream, an O-ring. It is a springless design, free of springs and poppets. [Vacuum generator] A venturi device that creates vacuum by flowing gas through a nozzle.
Although the circuit at the output side of the switch is surgeprotected, damage may still occur if a voltage surge is applied repeatedly. When a load which generates a surge, such as from a relay or solenoid valve, is directly driven, use a switch with a built-in surge absorbing element. 4. Since the type of fluid varies depending on the product, be sure to verify the specifications.
Do not connect the earth to a water pipe, a gas pipe, or a lightening rod. Do not plug too many leads into a single socket. That causes exothermic heat or fire. Do not modify the internal electrical wiring of the product. 10.2 Specifications An earth leakage breaker is installed in the product.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Seal guide B Slide plate Spacer Hexagon socket head cap screw MYMK-16-A MYMK-16-A MYMK-25-A MYMK-25-A MYMK-25-A Side seal unit Nickel plated Seal List No. !
(mm) At the minimum stroke of 25 mm adjustment bolt Basic stroke At maximum stroke adjustment At the minimum stroke of standard adjustment bolt Bore size (mm) Adjustment bolt fixing bolts Tightening torque Adjustment width across flats Bore size (mm) 10 15 25 10 15 25 A 2 A 26 A = 0.8 A = 0.6 A 0 M3 1.0 to 1.3 Nm 4 A 2 A 26 M5 4.6 to 6.2 Nm 5 Adjuster holder Adjuster holder A Adjustment
(mm) At the minimum stroke of standard adjustment bolt At the minimum stroke of 25 mm adjustment bolt Basic stroke At maximum stroke adjustment Bore size (mm) Bore size (mm) 10 15 25 Adjustment bolt fixing bolts Tightening torque Adjustment width across flats 10 15 25 A 2 A 26 A = 0.8 A = 0.6 A 0 M3 1.0 to 1.3 Nm 4 A 2 A 26 M5 4.6 to 6.2 Nm 5 Adjuster holder A Adjuster holder Adjustment
L R O D T H R E A D X A O P T I O N Thread Form Code M .
(mm) At the minimum stroke of 25 mm adjustment bolt Basic stroke At maximum stroke adjustment At the minimum stroke of standard adjustment bolt Bore size (mm) Adjustment bolt fixing bolts Tightening torque Adjustment width across flats Bore size (mm) 10 15 25 10 15 25 A 2 A 26 A = 0.8 A = 0.6 A 0 4 M3 1.0 to 1.3 Nm A 2 A 26 5 M5 4.6 to 6.2 Nm Adjuster holder Adjuster holder A Adjustment