AMG should be installed at the highest pressure and as far away as possible from the compressor. Particle and oil filter, plus pressure regulation if required, should be installed downstream of AMG. The element design produces negligible pressure drop. Note: AMG does not remove water vapour & air leaving AMG is 100% saturated. Where dehumified air (ie.
W W Mey Mep We We L3 A3 L2 A2 Note) Static moment : Moment by gravity Kinetic moment : Moment by stopper collision Max.allowable load:W max.
Note: Please take note at piping, which may lead to opposite setting. No.3The Change of Counter Direction OFFGoing to left will be an increment on counter. The origin is set to be at right. ONGoing to right will be an increment on counter. The origin is set to be at left.
When disassembling and reassembling the cylinder, please contact SMC or refer to the separate instruction manual. l2 l1 Approx. 0.5 or less l1 (mm) 5 5 l2 (mm) 8.4 9.5 CXSJ6 CXSJ10 Warning Piping 1. For axial piping, the side port of the standard cylinder is plugged. However, a plugged port can be switched according to the operating conditions.
When disassembling and reassembling the cylinder, please contact SMC or refer to the separate instruction manual. l2 l1 Approx. 0.5 or less l1 (mm) 5 5 l2 (mm) 8.4 9.5 CXSJ6 CXSJ10 Warning Piping 1. For axial piping, the side port of the standard cylinder is plugged. However, a plugged port can be switched according to the operating conditions.
10mA load current) 4V or less Internal voltage drop Leakage current 0.8mA or less at 24VDC 100A or less at 24VDC Operating position .
For setting the holding force to be at least Ex.)
(Full span) 6 l/min (ANR) (at supply pressure 0.9 MPa) Free Within 1% F.S.
Turn it in the counter-clockwise direction at 90o, and it is locked. Turn it right to release. 3.8 Change of electrical entry Wire entry can be changed by mounting the housing in either direction (four directions at every 90) after dividing the terminal block and the housing. For the indicator lighted style, be careful not to damage the light with the lead wire of the cable.
Mount a switch at the center of the operating range. Adjust the mounting position of an auto switch so that the piston stops at the center of the operating range (the range in which a switch is ON). (The mounting positions shown in the catalog indicate the optimum position at stroke end.)
o 85% RH lor lmin between and 50Mti or more (at belween bad wires and body In X. Y, Z directions 3limes each 12.6FS or lesis at 25'C 01: Rl/8. [.r5 x 0 8, Tl: NPT1/8, M5 x 0 8.
o 85% RH lor lmin between and 50Mti or more (at belween bad wires and body In X. Y, Z directions 3limes each 12.6FS or lesis at 25'C 01: Rl/8. [.r5 x 0 8, Tl: NPT1/8, M5 x 0 8.
[1] Power supply input terminals, L1, L2: Provide specified power supply to input terminals L1 and L2. [2] Connect the motor input terminal (U, V, W) to the driver power terminal (U, V, W).
7) 0V [1] Power supply input terminals, L1 and L2: Specify power supply to input terminals L1 and L2. [2] Connect the motor power supply input terminal (U, V, W) to the driver power terminal (U, V, W).
Allow at least 0.5 second from a locked stop (intermediate stop of the cylinder) until release of the lock. When the locked stop time is too short, the piston rod (and load) may lurch at a speed greater than the control speed of the speed controller. 5.
Pullthe valve up at the front.
(Coil temperature: 20C, pressure: 0.5 MPa, at rated voltage, with light and surge suppressor, value at operation excluding restart period) The period immediately after a restart may be delayed for about 1 msec depending on operating conditions. Note 2) Use dry air to prevent condensation when operating at low temperatures.
Dimensions n L 2 39 31 3 50 42 4 61 53 5 72 64 6 83 75 7 94 86 8 105 97 9 116 108 10 127 119 11 138 130 12 149 141 13 160 152 14 171 163 15 182 174 16 193 185 17 204 196 18 215 207 19 226 218 20 237 229 L1 L2 1.13-11