Configuration Minimum equipment and wiring requirements to get started 1 7 Provided by customer 100V AC /200 V AC Provided by customer 24 VDC Provided by customer 8 2 PC 6 4 Electric Actuators Ex) LEF Provided by customer 3 1 Driver LECSA*-S* 2 Motor cable LE-CSM-*** 3 Encoder cable LE-CSE-*** 4 I/O connector LE-CSNA I/O cable LEC-CSNA-1 5 USB cable LEC-MR-J3USB 6 Setup software (MR Configurator2TM
1 2 7 Eiector size determination by calculation: '1 .
1 2 7 Eiector size determination by calculation: '1 .
/N.O. type can be switched by supplying air to port 1(P) or 3(R). 2 way valves and selector valves can also be freely used. Type 40 Easy manual operation Since manual overrides are located in 2 directions, on the top and on the side of the valve, manual override operation is possible unaffected by mounting space and piping direction, etc.
[1] Power supply input terminals, L1, L2: Provide specified power supply to input terminals L1 and L2. [2] Connect the motor input terminal (U, V, W) to the driver power terminal (U, V, W).
The display End will be replaced by 0.0, leading to the input STEP 1. Input first setting position into STEP 1. Then, press WRITE to proceed to STEP 2. Set the following setting positions, STEP by STEP . After inputting the last data into last STEP , press WRITE, and then END to end the program setting.
Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3. Mount switches using the proper tightening torque. When a switch is tightened beyond the range of tightening torque, the mounting screws or switch may be damaged.
357 253.5 L2 81 322.5 127.5 196.5 300 162 231 369 265.5 L3 93 334.5 115.5 192.5 308 154 231 385 269.5 L1 77 346.5 VV2CS3 127.5 204.5 320 166 243 397 281.5 L2 89 358.5 139.5 216.5 332 178 255 409 293.5 L3 101 370.5 124.5 207.5 332 166 249 415 290.5 L1 83 373.5 VV2CS4 136.5 219.5 344 178 261 427 302.5 L2 95 385.5 148.5 231.5 356 190 273 439 314.5 L3 107 397.5 Manifold composition 3 stns. x
Surge voltage A high voltage which is momentarily generated in the shut-off unit by shutting off the power.
Order Made Power Saver Power consumption is decreased by 1/3 of standard product by reducing electrical power at holding. (This is effective when energizing time exceeds 62ms at rated voltage of 24V DC.) Specifications Operating principle 1 2 3 4 1 2 3 4 SY1 T SY1 AT SY Series Power consumption at holding is decreased with the below indicated circuit, for energy savings.
Note 2) Cylinder speed of CJ2 and CM2 is limited by the fixed orifice built-in. Note 3) Cylinder speed: when the cylinder is extended.
(VJA314) Air operated valve is controlled by external 3 port valve. External release is done directly from external 2 port valve. The following columns shall be filled in by SMC. Enter the ordering number in the table. Part no. Qty. Part no. Qty. Order no. Person in charge (Code no.) Section code 13-14-18 Date issued: 18 Photo copying this page is recommended.
Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3. Mount switches using the proper tightening torque. When a switch is tightened beyond the range of tightening torque, the mounting screws, or switch may be damaged.
Uni thread H D1 D2 L1 L2 L5 A Max.
Finger motion is synchronized by a rack and pinion mechanism.
An autoswitch can be mounted to indicate operation of the buffer, operated by a magnet on the piston. By reversing the direction of the switch, NO or NC operation is achievable.
Do not rotate the product by the indicator part. Use a wrench for mounting the product. Otherwise, it may cause damage to the product. 601
Balance the load by adjusting the air pressure in the front and rear sides of the cylinder with the load connected to the cylinder and the lock released. Lurching of the cylinder when unlocked can be prevented by carefully adjusting this air balance. Note) Can be used if all of the generated moment is absorbed by an effective guide. 2.
T M5 type H (width across flats) Applicable tubing O.D. d A A4 D1 L3 D2 M1 L1 T L2 Model Weight (g) Note 2) Tubing O.D. d T H D1 D2 L1 L2 L3 M1 L4 Max.