HRX-OM-T004 Refer to 4.3.2 Setting and checking,5.3.2 Setting and checking. 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers.
Excess at no communicatio n monitoring time. Broken wire o r coming off 60 sec. 60 sec. AL19 Communication error is generated.
Applicable model Flow rate (l/min) Rc NPT G Nil N F Symbol 40 4 16 3/8 1/2 3/4 PFW504, 520 PFW520, 540 PFW540 03 04 06 Specifications Model Measured fluid Detection type Flow rate measurement range Operating pressure range Withstand pressure Operating temperature range Power supply voltage Current consumption Weight Enclosure Port size (Rc, NPT, G) PFW520 PFW504 PFW540 Water Karman
Note 5) Spare part for auto drain INA-20-41-04 is AD44-x445. Operation Principles IDU3D Drain separator Compressed air inlet Compressed air outlet Humid hot air entering the air dryer is cooled in the aftercooler (air-cooling style) and then further cooled by the cooler. At this time, the condensed moisture is separated from the air by the drain separator and automatically discharged.
7.5 52 37 20 2 x M4 x 0.7 Female mounting threads Thread depth 6 2 x 4.5 Mounting hole 66 14 14 Foot (Option) 3 2 x M4 x 0.7 Female mounting threads Thread depth 6 AIR SUP Rc, NPT, G 1/8 FLUID IN Rc, NPT, G 1/8 20 8.5 15 8 10 18 Caution 1.
resistance 980 m/s2 X, Y, Z directions, 3 times each Enclosure IP40 (IEC standard) Weight Approx. 100 g (Unit 50 g, batteries 50 g) 2 pcs. of type AA dry batteries (manganese R6 or alkaline LR6) are not included.
resistance 980 m/s2 X, Y, Z directions, 3 times each Enclosure IP40 (IEC standard) Weight Approx. 100 g (Unit 50 g, batteries 50 g) 2 pcs. of type AA dry batteries (manganese R6 or alkaline LR6) are not included.
at rod end indicates the value in rod end female thread.
at rod end indicates the value in rod end female thread.
If the cylinder is operating at a high frequency, be aware that the cylinder tube surface could become very hot, creating the risk of burns. If the cylinder is operating at a high frequency, be aware that the cylinder tube surface could become very hot, creating the risk of burns. eThe One-Touch fitting cannot be replaced.
D-M9/M9W D-M9A/A9 Note 1) The mounting position should be referred for reference only for the auto switch mounting position at the stroke end detection. Adjust the auto switch after confirming the operation to set actually. Note 2) The auto switch mounting position is temporarily set at the time of shipping from our factory.
Mount a switch at the center of the operating range. Adjust the mounting position of an auto switch so that the piston stops at the center of the operating range (the range in which a switch is ON). (The mounting position shown in the catalog indicates the optimum position at stroke end.)
Note 3) When using seal material PTFE at 15 cm3/min (under water pressure) or less. Note 4) Vibration resistance Conditions when tested with one sweep of 10 to 250 Hz in the axial direction and at a right angle to the armature, in both energized and deenergized states. No malfunction occurred when tested (value at the initial state).
load at the rod end is for rod end female thread.
G Rear flange F Front flange L Foot C Male rear clevis D Female rear clevis 1.8-29
Stainless Steel (mm) A B C D E F G H J L Bracket part no.
Weight (g) d T H D1 D2 D3 L1 L2 L3 Model 4 ASD230F-M5-04 9.3 29.4 12 17.5 12.9 25.5 28.6 25.8 10 9.6 7.8 11.7 M5 x 0.8 28.3 8 25 22.2 6 ASD230F-M5-06 11.6 32.5 13 13.7 20.6 6 34.6 ASD330F-01-06S 14 39.6 11.6 29 13.7 38.5 22.9 36.1 31.1 11.8 14.2 10.6 R 1/8 12 32.1 27.1 15.8 8 33.9 ASD330F-01-08S 38.9 15.2 31 18.5 44.8 28.2 6 ASD430F-02-06S 12.8 53 17 43.5 25.2 18 8 ASD430F-02-08S 36.7 41.7
sub-plate Without sub-plate 1 2 3 Nil 02 03 13 9 5 Symbol 2 1/4 Nil 02 03 0.05 to 0.65MPa 1 3/8 2 1/4 2 0.1 to 0.9MPa 2 02 03 04 03 04 06 1/4 3/8 1/2 3/8 1/2 3/4 1 2 3 4 3/8 03 04 06 3 1 30 3/8 0.005 to 0.15MPa 1 4 1/2 4 45 1 3/4 12 8 4.5 2.5 Without sub-plate Nil 02 03 1(P) Symbol Flow type (VEF2) Flow type (VEF3) Pressure type (VEP3) 2 2(A) 1/4 3 3/8 2(A) 2(A) 1(P) 3(R) 1(P) 3(R) 03 04