CY1F

Operate the piston within a range such that collision damage will not occur at the stroke end. 5. Consider a possible drop in operating pressure due to a power outage, etc. When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc.

Magnetically Coupled Rodless Cylinder

(The switch will stay ON all the time.) 1) For an auto switch without a contact protection circuit, use a contact protection box when the wire length is 5m or longer. 7. Do not use a load that generates surge voltage. If driving a load such as a relay that generates a surge voltage, use a contact protection box.

Intrinsically Safe Valve

The solenoid must be connected to a safety barrier located in a non-hazardous area.

AS

AS22;1F-01-23(S)A 3.2 7.2 9 (9) AS22;1F-01-04(S)A 4 8.2 19.1 26.1 (26) 13.3 13 AS22;1F-01-06(S)A 19.1 6 1/8 10.4 11.6 30.6 29.2 27.5 26.1 10 (9) (12.7) AS22;1F-01-08(S)A 8 13.2 22.4 29.4 (29.3) 14.2 11 (10) AS22;1F-01-10(S)A 10 15.9 25.3 32.3 (32.2) 15.6 12 (11) AS22;1F-02-23(S)A 3.2 7.2 20.9 30 (30.3) AS22;1F-02-04(S)A 4 8.2 13.3 18 (19) 17 AS22;1F-02-06(S)A 22.6 6 1/4 10.4 12.6 23.4 32.5

VDW

A Common Specifications N.C.

MY2

If driving a load such as a relay that generates a surge voltage, use a contact protection box. Although a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if the surge is applied repeatedly.

Pilot Operated

0 A !3 !2 !1 o i t !0 !3 !2 !1 o i e t !0 A A e u w y q B C P2 P1 OUT IN P1 w y u B q w y u B q P2 OUT C C IN VXD2272/2382/2392 (32A to 50A) VXD2270/2380/2390 (32A to 50A) !4 !5 !3 !1 i t e !2 !0 A r u B y q !3 !2 !1 i t e o !0 A r u B y q w o w C C Operation When the coil !

2–4

Although a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if a surge is applied repeatedly. When directly driving a load which generates surge, such as a relay or solenoid valve, use a type of switch with a built-in surge absorbing element. 8.

Compact Type

Therefore, do not use a cylinder without a bumper bolt. Furthermore, if the bumper bolt is tightened without a nut, the piston seal is caught in the leveled part, damaging the seal. 3. A bumper at the end of the bumper bolt is replaceable. In case a missing bumper, or a bumper has a permanent settling, use a following part numbers for ordering.

48

7 u A A A-A (LEL25LT-n) A-A (LEL25MT-n) !9 !9 t @0 @1 !0 !6 !8 !5 o Component Parts Description No.

Smooth Cylinder

Vertical actuation (Speed control) I II P2 W A P1 a B A P0 P0 a A W (1) Basically, meter-out control is used. Combine meter-in control to reduce sudden movement. (1) Basically, meter-out control is used.

Electric Actuator

To prevent danger and damage due to a breakdown or malfunction of these products, which may occur at a certain probability, a backup system should be arranged in advance by using a multiple-layered structure or by making a fail-safe equipment design, etc. 13. Avoid heat radiation from strong heat sources, such as direct sunlight or a hot furnace.

CU

A + A' A' w After piston seal H has passed air passage A, air is exhausted only through A'. The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved. A A' A' e When air is supplied for the piston extension, the check valve opens and the piston extends with no delay.

Compact Vacuum Unit

When the product is mounted so that the exhaust port side will be against a wall, use a spacer to secure a clearance of at least 0.039 inch (1 mm). (Fig. 1) For the single unit, PV port and PD port are oriented downward. When it is installed on a working table, use a bracket for single unit (Fig. 2) or secure a space for piping underneath the ports.

/

Connection of piping to products When connecting piping to a product, refer to its instruction manual to avoid mistakes regarding the supply port, etc. 6. Steam generated in a boiler contains a large amount of drainage. Be sure to operate it with a drain trap installed. 7.

3 Port Solenoid Valve

and V124(A) cannot be mounted to the same manifold.

Standard Combinations

To release residual pressure, select a model with a back flow mechanism.

Precautions 1

R1 ND MM ND MM R1 MM E1 ND NX1 A U1 R2 H Z E1 NX U1 L1 A A NX A1 (Min.) A1 U1 L1 Applicable bore size 20 25, 32 40 MM L1 NX NDH10 R1 E1 A1 U1 A A H MM NDH10 NX1 U1 R2 Y Z Part no.

Series KV2 Fittings

Dont use a wrench on push-to-connect end. 2 2 Cut tubing square with a clean 90 edge Dont use excessive tube angle cut which can lead to leakage or breaking. 90 90 3 3 Use SMC Tube Cutters Dont use dikes, a knife, a saw or a dull tool to cut the tubing.

Clamp Cylinder with Lock

the tube surface of a closely mounted built-in strong magnet type cylinder by 30 mm or more. 3) When a built-in strong magnet type cylinder and a cylinder with a general-purpose auto switch are closely positioned, separate the cylinder tubes 50 mm or more. 4) Separate a general-purpose auto switch from the tube surface of a closely mounted built-in strong magnet cylinder by 50 mm or more