0.5 US Edition B Safety Instructions Be sure to read the Handling Precautions for SMC Products (M-E03-3) and Operation Manual before use.
Power supply 24 VDC B B B Ground with a ground resistance of 100 or less without connecting the DC1 () lead (Blue) of the power supply cable to the power supply 0 V. Red A A +24 V Black Blue Charged object Charged object 0 V Reduced-wiring Fieldbus System F.G. (mm) Ground with a ground resistance of 100 or less. A B When using the autobalance sensor (body-mounting type) 10 20 20 40 3.
ZX B B' A B ZR A B P1 A A' ZM !0 o r t ZH ZU Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com e ZL ZY ZQ ZF ZP !1 ZCU Section A-A' (Ejector) AMJ !
The C76 series air cylinders offer a simple, space saving design with high dimensional accuracy, making these cylinders very easy to use. Large spanner flats on the rod and head covers greatly simplify their installation and positioning. Low friction and the standard elastomer cushion rings allow piston speeds up to 1500mm/sec. Greater side loads are allowed due to the close tolerance of
The C76 series air cylinders offer a simple, space saving design with high dimensional accuracy, making these cylinders very easy to use. Large spanner flats on the rod and head covers greatly simplify their installation and positioning. Low friction and the standard elastomer cushion rings allow piston speeds up to 1500mm/sec. Greater side loads are allowed due to the close tolerance of
Thus, in spite of using pneumatic equipment, it performs similarly to a RE A B REC CX CY MQQ M A selection of valve unit is available to suit your application. High cylinder driving speed.
C A External pilot type R (2) B C A Note 1) Option Note 2) For details about external pilot specifications, refer to page 4-14-40.
Catch the hook of the DIN rail bracket on the (b) side on the DIN rail. 2. Push side (a) onto the DIN rail and tighten the clamp screw.
B Released SET Work 1 Work 2 Work n Atmosphere Max. A: Maximum pressure value when workpiece is adsorbed. A B 4 ON = A A B 4 SET OFF = B + Min. B: Minimum pressure value when workpiece is not adsorbed. OUT1 auto preset For adsorption verification: In this mode, repeat the adsorption and release of the workpiece for a few times. The optimum values will be set automatically.
P-1 = A (A B) / 4 H-1 = (A B) / 2 A = Maximum pressure value B = Minimum pressure value For low differential pressure For low pressure For compound pressure PSE533 PSE543 PSE563 For positive pressure For vacuum Pressure range C Display calibration function This function eliminates slight differences in the output values and allows uniformity in the numbers displayed.
High Suction Vacuum Work 1 Work 2 Work n Max.A ON point OFF point Min.B Not adsorption Work 1 Work 2 Work n Atmosphere A B 4 A B 4 = A ON point Max.A: Maximum pressure value when workpiece is vacuumed. Min.B: Maximum pressure value when workpiece is not vacuumed.
A B PF3W504 0 4 PF3W520 0 16 PF3W540 0 40 PF3W511 0 100 Display A Set A and B to the values shown in the table on the left.
B Released SET Work 1 Work 2 Work n Atmosphere Max. A: Maximum pressure value when work piece is adsorbed. A B 4 ON = A A B 4 SET OFF = B + Min. B: Minimum pressure value when work piece is not adsorbed. OUT1 auto preset For adsorption verification: In this mode, repeat the adsorption and release of the work piece for a few times. The optimum values will be set automatically.
Note Bracket B and the bracket assembly make up one set.
(B contact) 3 wire GXL-N12FTB Switch specifications (SUNX Corporation) GXL-N12FT(B) Part no.
VE System A System B START VY RUN START G AL Analog voltage input 0 to 10V PLC START Robot support (External input operation) RUN START After both systems A and B have been auto balanced, an operation command is input to the controller to operate the cylinder. At the point at which the auto switch for stopping has been tripped, systems A and B are stopped to assemble parts.
High Suction Vacuum Work 1 Work 2 Work n Max.A ON point OFF point Min.B Not adsorption Work 1 Work 2 Work n Atmosphere A B 4 A B 4 = A ON point Max.A: Maximum pressure value when work piece is vacuumed. Min.B : Maximum pressure value when work piece is not vacuumed.
Symbol Nil N F Option Option Symbol Applicable actuation Built-in solenoid valve Air Operated PB1013A Air operated Port size Port size 1/8 Nil B N None With foot With silencer Symbol 01 When option is more than one, suffix in alphabetical order.
Step (3) Select required function for valve unit Select a model from data (B),
For IITV00-n Total weight (g) Stations (n) x 100 + 130 (Weight of end block A, B assembly) + Weight (g) of DIN rail Note 2) Specifications other than the following are optional.