Series CQ2 Maintain a minimum cylinder separation of 40mm. 3. Pay attention to the length of time that a switch is ON at an intermediate stroke position.
If 12VDC specifications are required, enter "12" at the end of the assembly part number. 1 2 1 2 P N D side SZ3000-40-6A-D For flat cable 20 pins SZ3000-40-5A-D 1 2 P N 1 2 D side SZ3000-40-8A-D For flat cable 10 pins SZ3000-40-7A-D A connector block assembly can be shipped as an assembly only in the case of double wiring.
In sucn a case use the 3-wire type. 6. Do not use a load which generates a surge voltage. (Solid-state switch) An output part connected to a zener diode for protection against surge may be damaged by repeated surges. Use an auto switch with built-in surge absorbing element when directly driving a load that generates a surge such as a relay or solenoid valve. 7.
10-SV4000 40 or less 40 or less 82 or less 3 position exhaust center 2(B) (A)4 2(B) (A)4 2 position single 2 position double 3 position (EA)5 1 (P) 3(EB) (EA)5 1 (P) 3(EB) 4 position dual 3 port valve 3 position pressure center Note) Based on dynamic performance test, JIS B 8375-1981 (Coil temperature: 20C, at rated voltage) 2(B) (A)4 2(B) (A)4 Weight (EA)5 3(EB) 1 (P) (EA)5 1 (P) 3(EB
re galge: AW20K to 30K-l /8t AW40K-j/4 Pressure gauge ls nol mounted at lhe r me orshrpme.t blt lher packagd 1oglherwth thei ter regulatortorshpme.t a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a o a a a a a a a a a a a ra a Oplional Symbol Descflpllon Applicable Meialbowl AFD20 to 40 Nylon bo\,rl AFD20 io 40 [4etal bowlwth level gauge AFD3O 40 Wlh bow guard AFDZO
Furthermore, since valves and cylinders are not guaranteed for zero air leakage, it may not be possible to hold a stopped position for an extended period of time. Contact SMC in case it is necessary to hold a stopped position for an extended period. Caution 1. Use a speed controller to adjust the cylinder drive speed, gradually increasing from a low speed to the desired speed setting.
Instead, use an individual CC valve unit or a speed controller (AS2000, AS3000, AS4000, etc.) through a pipe connection.
1 Rotary Cylinder Series MRQ Size: 32, 40 A rectilinear rotation unit that compactly integrates a slim cylinder and a rotary actuator. CRB2 CRBU2 CRB1 The timing of the rectilinear and rotational movements can be set as desired. Rotational movements are possible at the forward end, the back end, or during a rectilinear movement.
Type 40/41 How to Order 10--SS3YJ7-40 -05 --01 Applicable solenoid valve 10-SYJ714M10-SYJ724MR port 1/4 R port 1/8 Clean series Applicable blanking plate assembly SYJ700-10-2A Manifold P, R port thread 40 41 Type 40 Type 41 Stations Nil Rc G NPT NPTF A A A A 2 stations : 20 stations 02 : 20 F N T P Port 1/8 P Port 1/4 01 1/8 A port size A port 1/8 A port 1/8 Note) For more than 6 stations
When using a cylinder with long strokes, implement an intermediate support. When using a cylinder with long strokes, implement an intermediate support to prevent the tube from sagging and being deflected by vibration or an external load. Refer to the Guide to Side Support Application on page 1195. 2. For intermediate stops, use a dual-side pressure control circuit.
CCT40 Effective oil level stroke Specifications 0 to 0.7MPa Operating pressure Because the CCT40 is a converter for an actuator with a small capacity, it cannot be made into an air-hydro unit.
Pressure (including vacuum) holding It is not usable for an application such as holding the pressure (including vacuum) inside of a pressure vessel because air leakage is entailed in a valve. 8. When the conduit type is used as equivalent to an IP65 enclosure, install a wiring conduit, etc. 9.
Note 1) R block valve is mounted in the blocking position when ordering an individual EXH spacer incorporated with a manifold. When separately ordering an individual EXH spacer, separately order a R block valve.
A: Order the press cylinder with a non-rotating rod option. Collet Fixtures Q: Is there a way of firmly holding smooth round bars with an air powered device? A: Use an air collet fixture. The device operates just like a double acting cylinder; air to close and open.
A: Order the press cylinder with a non-rotating rod option. Collet Fixtures Q: Is there a way of firmly holding smooth round bars with an air powered device? A: Use an air collet fixture. The device operates just like a double acting cylinder; air to close and open.
to 100 5 to 395 Part no.: MGPA20-39 A spacer 1 mm in width is installed in a MGPA20-40.
Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 2. Consider stopping accuracy and the amount of overrun when an intermediate stop is performed. Due to the nature of a mechanical lock, there is a momentary lag with respect to the stop signal, and a time delay occurs before stopping.
(mm) L2 (mm) L3 (mm) Pitching Rolling Yawing m : Transfer load (kg) a : Work piece acceleration (mm/s) Me: Dynamic moment L : Overhang to work piece center of gravity (mm) a = 2000 m 1000 L1 a = 3000 0 20 40 60 Transfer load m (kg) 600 L2 400 Mer m 200 L2 Mer 0 20 40 60 m Transfer load m (kg) 2000 a = 1000 L3 1000 a = 2000 m a = 3000 Mey a 0 20 40 60 Transfer load m (kg) Refer to page 145
AD27-2-A AD37m-2-A AD47m-2-A With level gauge AD37m-8-A AD47m-8-A Normally open (N.O.) AD38m-2-A AD48m-2-A With level gauge AD38m-8-A AD48m-8-A Automatic (Auto drain) The bowl assembly for sizes 20 to 40 comes with a bowl seal. The bowl assembly for sizes 50 and 60 comes with a flange and a bowl seal.
A-q A-w A-e A-r A-t A-y A-u A-!1 A-y A-u A-!2 A-!