Compact Vacuum Ejector Series ZQ Left Right 15 -60 -60 10 -40 -40 Air consumption -20 -20 5 S 1 S 2 R U N L HL H S 1 S 2 R U N L HL H S 1 S 2 R U NL HL H S 1 S 2 R U NL HL H S 1 S 2 R U N L HL H S 1 S 2 R U N L HL H S 1 S 2 R U N L HL H S 1 S 2 R U N L HL H kP a M O DE SET1 SET2 kP a M O DE SET1 SET2 kP a M O DE SET1 SET2 kP a M O DE SET1 SET2 kP a M O DE SET1 SET2 kP a M O DE SET1 SET2 kP a M O DE SET1 SET2 kP a M O DE
ZF Left Right 15 -60 -60 ZP 10 -40 -40 Air consumption ZCU -20 -20 5 S 1 S 2 R U N L HL H S 1 S 2 R U N L HL H S 1 S 2 R U NL HL H S 1 S 2 R U NL HL H S 1 S 2 R U N L HL H S 1 S 2 R U N L HL H S 1 S 2 R U N L HL H S 1 S 2 R U N L HL H kP a M O DE SET1 SET2 kP a M O DE SET1 SET2 kP a M O DE SET1 SET2 kP a M O DE SET1 SET2 kP a M O DE SET1 SET2 kP a M O DE SET1 SET2 kP a M O DE SET1 SET2 kP
Size ASF Model d T Weight (g) H D1 D2 L1 L2 L3 L4 A Model d T Weight (g) H D1 D2 L1 L2 L3 L4 A Max.
The dimensions are the same as the standard type. MHW2 Groove position of auto switch A Model MHK2-12l MHK2-16l A 10.4 12.8 B 1.8 1.6 MRHQ B Auto switch Standard switch grooves Dimensions A and B other models are same as standard switch grooves. 2.4-17
When an offset load is expected, provide a suitable mechanism such as a floating joint. 2) Use clean air (atmospheric pressure dew point temperature 10C or less). Use of a series AM mist separator (filtration rating of 0.3 m or less), or series AM + AMD (filtration rating of 0.01 m or less) is recommended.
When an offset load is expected, provide a suitable mechanism such as a floating joint. 2) Use clean air (atmospheric pressure dew point temperature 10C or less). Use of a series AM mist separator (filtration rating of 0.3 m or less), or series AM + AMD (filtration rating of 0.01 m or less) is recommended.
As a rough guide, use a precision screwdriver that has a gripping diameter of 5 to 6 mm, and turn 90 from the position in which it comes to feel tight. q As shown in Fig. 1-1, turn the set screw (c) into the nut (M3) of the auto switch mounting band (b.
A-q A-w A-e A-r A-t A-y A-u A-!1 A-y A-u A-!2 A-!
As a rule, adjust the dimensions of L2 to a range lower that the value given in Table (2). Urethane bumper If you do not adjust the urethane bumper so it can work effectively, the devices lifespan will be adversely affected because the impact of collisions will be greater. As a rule, adjust the dimensions of L1 to a range lower that the value given in Table (1).
Hs A B A B Proper Auto Switch Mounting Position (mm) D-A7H, A80H, A73C, A80C D-F7, F7V, F79F, J79 D-J79C, F7W, F7WV D-J79W, F7BAL, F7BAVL D-A7 D-A80 D-F7NTL D-A79W Bore size (mm) B B A A B A B A 32 3 11 51 43 6 46 5.5 45.5 40 5.5 13.5 49.5 57.5 8.5 52.5 8 52 50 19 11 53.5 61.5 14 56.5 13.5 56 63 22 14 59 67 17 62 16.5 61.5 Auto Switch Mounting Height (mm) D-A7H, A80H D-F7, J79, F7W D-J79W
For using as a Pick & Place unit in combination with other actuators.
a guide only, this should not be viewed as a guarantee of our products performance.
Connect a DC () wire (blue) as close as possible to the DC power supply GND terminal. Connecting the power supply away from the GND terminal can cause malfunctions due to noise from devices that are connected to the GND terminal. 2. Do not attempt to insert or pull the pressure sensor or its connector when the power is on. 3. A cable with a right-angled connector is also available.
Applicable air preparation equipment VHS20 VHS30 VHS40 VHS40-06 VHS50 Y200-A Y300-A Y400-A Y500-A Y600-A AC20-A AC25-A, AC30-A AC40-A AC40-06-A AC50, AC55 Note), AC60 Note) Y200T-A Y300T-A Y400T-A Y500T-A Y600T-A Note) VHS50 can be connected to AC55 and AC60.
Please note that the graph should only be used as a guide as there is a tolerance of about 10% in the clamp cylinder body.
System configuration Make sure to install a mist separator (Series AM) on the inlet side of the booster valve. Also install a cleaning device such as an air filter or a mist separator on the outlet side as necessary. Because the booster valve contains a sliding mechanism and the inner wall of the tank for the booster valve is untreated, dust flows out to the secondary side.
Install a solenoid valve for braking as close to the cylinder as possible. If there is a long distance between the cylinder and valve, it may cause fluctuations in the stop accuracy or unexpected sudden slide table movements.
Use a cylinder with a built-in cushion mechanism. When a driven object is stopped, ensure the impact force of the object being transferred to the floating joint is prevented by using a cylinder with a built-in cushion mechanism (rubber cushion or air cushion). To stop the cylinder at the intermediate position, use an external shock absorbing mechanism such as a shock absorber.
Furthermore, the switch unit should be kept as close as possible to the contact protection box, with a lead wire length of no more than 1 meter between them. Note) Hysteresis may fluctuate due to the operating environment, and is not guaranteed.
D-C7/C80 D-H7/H7W/H7F/H7BA 8.5 Hs Hs 8.5 16 16 B Auto switch 29 A 26 A Auto switch B D-C73C/C80C D-H7C Hs 8.5 Hs Auto switch 16 16 B Auto switch 38.2 A A 36.7 B D-G5/K59/G5W/K59W/G5BA/G59F/G5NT D-B5/B64/B59W Hs Hs 12 Auto switch 12 24.5 24.5 A B A B Auto switch 33 6.5 33 D-A3/G39/K39 D-A4 Hs Auto switch 36 Hs 36 Auto switch B A B A 49 49.5 G 1/2 (applicable cable 6.8 to 11.5) G 1/2 (applicable