IDX-OM-P023E Fig. 3 1) Follow the users own procedure to keep operators safe. (E.g.
Fig. 3 1) Follow the users own procedure to keep operators safe. (E.g.
Please refer to "Fig.1 Allowable lateral load applied to rod end" (Page 8) Table 2 Operating range and kinetic energy Bore size 6 10 16 Allowable kinetic energy 0.12 J 0.035 J 0.090 J Warning Operate the actuator with allowable kinetic energy (Table 2) or less.
IP address setting of the IP Address Setting Tool 8 7. Option Setting 11 8. Log monitor function 11 9. Export Function 12 10. Troubleshooting 13 11. Definitions and Terminology (Supplementary Explanation) 15 -1No.EX-OMV1026-B 1.
1/2 3/8 1/2 1/2 1/2 Type M 2.7 3.2 3.3 2.7 3.2 3.3 Mass kg Type V 3.1 3.7 3.8 3.1 3.7 3.8 * Note 1.
The following description uses the manifold configuration example shown in Fig. 1.
Dew point checker (Option : S) Air inlet port * Outlet port in case of Option R Body Purge air outlet port Case Front Fig 2.1 Names of parts -3- 2. Installations and Operations 2. Installations and Operations: Piping Air Supply Warning a.
Tightening torque : 1.4 Nm Hexagonal key : nominal 4 Fig 2.1 Names of parts Caution a. Consider the purge air flow rate in total flow rate requirements. Find the purge air flow rate from the charts and calculate the required outlet air flow rate + purge air flow rate.
Drain Port of Upstream Side (Port to discharge removed water inside case) Pressure gauge Port of Upstream Side Fig. 1 Construction Table. 1 Part Name MAINTENANCE PART No.
.1 Fig.2 Fluid flow Air flow 11 -
Caution When the old version parameter file is read, the display shown in the Fig. will be displayed. Check and set the parameters again. Refer to the operation manuals for the controller for details of the set items. Caution When the parameter file with a problem is read, the display shown in the Fig. will be displayed.
Product Nominal Proper tightening Product Nominal Proper tightening thread size torque (Nm) thread size torque (Nm) ISA3 Rc1/8 G1/8 3 to 5 Regulator Rc1/4 G1/4 8 to 12 OUT port (detection port) Use the correct tightening torque. Refer to the following table for the appropriate tightening torque.
2 to 12 stations (24) 2 to 8 stations (16) 2 to 12 stations (24) 2 to 8 stations (16) VFS M12 PROFIBUS DP VFR D-sub Note 4) M12 CC-Link VQ7 M12 EtherCAT IP67 compliant M12 PROFINET SI unit: EX126 IP40 compliant 1 to 8 stations (16) CC-Link SI unit: EX260 IP67 compliant SDVB M12 EtherNet/IP kit (Flat ribbon cable) kit (D-sub connector) kit (Terminal block box) F P T Note) For a 20P flat ribbon
Size: 01 (Size 01), Passage Symbol: FIG (3 Position Pressure Center), Number of Solenoids: D (Double), Rated Voltage: 3 (24 VDC), Light/Surge Voltage Suppressor: Z (Light/Surge Voltage Suppressor), Sealing Type: Metal Seal, Port Size: A01 (Side Ported, 1/8), Thread: F (G)
Passage: FIG (3-Position, Pressure Center), Solenoid: D (Double), Voltage: 3 (24V DC), Option: N (Indicator Light), Seal: Metal Seal, Subplate: A03 (Side Ported 3/8)
Passage: FIG (3-Position, Pressure Center), Solenoid: D (Double), Voltage: 3 (24V DC), Option: N (Indicator Light), Seal: Metal Seal, Subplate: A03 (Side Ported 3/8), Thread: Rc, Connector: SC (Pre-wired Connector)
Passage: FIG (3-Position, Pressure Center), Solenoid: D (Double), Voltage: 3 (24V DC), Option: N (Indicator Light), Seal: R (Rubber Seal), Subplate: A03 (Side Ported 3/8), Thread: Rc, Connector: SC (Pre-wired Connector)
Passage: FIG (3-Position, Pressure Center), Solenoid: D (Double), Voltage: 3 (24V DC), Option: Z (Indicator Light w/Surge Voltage Suppressor), Seal: Metal Seal, Subplate: A03 (Side Ported 3/8)
Passage: FIG (3-Position, Pressure Center), Solenoid: D (Double), Voltage: 3 (24V DC), Option: None, Seal: Metal Seal, Subplate: A03 (Side Ported 3/8), Thread: Rc, Connector: SC (Pre-wired Connector)
Passage: FIG (3-Position, Pressure Center), Solenoid: D (Double), Voltage: 3 (24V DC), Option: Z (Indicator Light w/Surge Voltage Suppressor), Seal: R (Rubber Seal), Subplate: A03 (Side Ported 3/8), Thread: F (G)