W2M/4M Before piping and screwing in couplings, please make sure that sludge trom pipe threading and sealing materials do not go into the pipe. When seal tape is used, tape winding should be done so that 2 threads are left untaDed on the end.
Do not attempt to rotate, as it does not turn Cable connection threads RC(PT) 1/4 Exhaust porl EXH (3) Port size 4-M5 x 0 8 thread depth 6mm Mounting hole 2-RC(PT) 1/4, 3/8 SUP port, OUT porl rTl|z000/3000 tleflru-Pltotllnalic Re[ula 0imeffiiolt$ ITV3OtrT Cable connector (4 wire) Cable connector (4 wire) . Do not anempt to rotate. as it does not turn.
NCf,IW NCDMW 'Noie: lf ordered do rubber bumper, orcrall length docreases .25 inches. o svE' Stainless Steel Cylinder Air Cylinder Series NCM Specifications 250 PSt(17.5 kgf/cm') 8 PSI (0.5 kgf/cm'?)
Do not use fluid which corrode the wetted parts material. 2. Do not use the products for medical or food applications. 3. The applicability may vary depending on additives. Take note also of additives. 4. The applicability may vary depending on impurities. Take note also of impurities. 5. Examples of transfer liquids are shown in the table on the left.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Do not service machinery/equipment or attempt to remove component until safety is confirmed. 1) Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions. 3-12-6 A
Do not use a screwdriver with a large grip or with a tip that does not fit into the trimmer groove because this could strip the groove.
D DIN terminal DL DIN terminal with light DO DIN terminal (without connector, with gasket) Orifice diameter and Port Size Combinations T Conduit terminal Class Orifice diameter (mm) Port size 2 4 3 7 5 10 1/8 ( 6A) V V V V 2 1/4 ( 8A) V V V V 1/4 ( 8A) V V V V 3 3/8 (10A) V V V V V 1/2 (15A) V Connector 1/4 ( 8A) V V V V 3/8 (10A) V V V V V All class B coils come with surge
Caution Do not apply excessive torque when turning the locking type manual override. (0.1 Nm or less) 2-4-90 Body Ported Series VQ1000 Plug Lead Unit: Cassette Type How to Mount/Remove Solenoid Valve How to Calculate the Flow Rate Caution Caution For obtaining the flow rate, refer to pages 2-1-8 to 2-1-11.
Do not apply a lateral load on the main body during or after mounting. 3. When the silencer has loosened due to vibrations from the mounted equipment, mount the silencer after applying an anti-loosening agent to the thread. 612
How to Order Do not replace heavy duty scrapers. XC4 Since heavy duty scrapers are press-fit, do not replace the cover only, but rather the entire rod cover assembly. The CM2 series cannot replace either heavy duty scraper or rod seal. (It goes for replacing retainer assembly for the CS1 series.) Replace the CNA2 series with the lock unit.
Electrical entry 1/4 (AV2000 only) 3/8 (AV3000 only) 1/2 (AV4000 only) 3/4 (AV5000 only) 1 (AV5000 only) 02 03 04 06 10 G: Grommet Coil rated voltage 1 2 3 4 5 6 7 9 100 VAC (50/60 Hz) 200 VAC (50/60 Hz) 110 to 120 VAC (50/60 Hz) 220 VAC (50/60 Hz) 24 VDC 12 VDC 240VAC (50/60 Hz) Other D: Type D DIN terminal (With connector) Option Nil G None With pressure gauge How to Order Pilot Valve Assembly DO
Do not cut the tube with cutting pliers, nippers, scissors, etc.) 2. Grasp the tube, then slowly push it until it comes to a stop. 3. Then, pull it back gently to make sure that it does not come out.
Model (Standard) Dimensions Pressure range (1) Connection thread Indication unit Model G15 MPa MPa G15-10-01 (2) R 1/8, M5 (Female thread) 0 to 1.0 0 to 1.0 1 16 G27-10-R1 R MPa Note 1) Do not apply more excessive pressure than max. pressure display. It will be a cause of malfunction.
Hz) 1 2 3 Symbol Symbol Port size Thread type Sub-plate A B 1/8 1/4 Rc G NPT NPTF Nil F N T 4 5 6 7 Base gasket VEX1 11 2 9 Other Option Body size Port size Electrical entry (Only with solenoid) Port size Body size Electrical entry Port 1(P), 2(A) 3(R) 1 8 1 8 01 1 02 G Grommet (Lead wire length 300 mm) 1 4 1 4 H Grommet (Lead wire length 600 mm) 1 4 1 4 02 3 03 D DIN terminal 3 8 3 8 DO
Caution D: With connector DO: Without connector Y: With connector YO: Without connector When using the surge voltage suppressor type, residual voltage will remain. For details, refer to the Web Catalog (VP300/500 Low wattage specication). * Refer to the Web Catalog (VP300/500 Low wattage specication) for details of the DIN terminal. Assembly Example Products do not come assembled.
Because suctioned matter is ejected together with exhaust, do not direct an exhaust port at a person or equipment. AFJ AMV 2.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed.
Do not supply or discharge air suddenly. This will cause the temperature to decrease due to air expansion, and the temperature may exceed the operating temperature limit of the air tank. If flow speed becomes faster, a loud noise may be generated by the friction inside the tube.
Do the drain pulling out regularly.