IN20267 Figure 18-1 SMD Cover 49 - IN20267 Figure 18-2 Defualt Switch Position all up 50 - IN20267 Revision History Revision Description Date Author(s) 1.0 Initial release for Ethernet/IP MPC 010/11/2016 SMC US EPG SMC Corporation of America 10100 SMC Boulevard Noblesville, IN 46060 Phone: 1-800-SMC-SMC1 (1-800-762-7621) URL: www.smcusa.com 51 -
Franklin Road Indianapolis, Indiana 46226 1-800-SMC-SMC1 (762-7621) www.smcusa.com US98-E464 12/99 Solid State Vacuum Regulator Series ITV2090/2091 Stepless control of vacuum pressure in proportion to an electric signal Able to operate with vacuum only Pilot air required by the previous series (IT209) is unnecessary Air consumption is approximately 0l/min (ANR) (when balanced) Two types of
VCA20-12-1A VCA30-12-1A VCA40-12-1A Connector All types equipped with surge voltage suppressor. 1 Direct Operated 2 Port for Air Series VCA Standard Specifications Direct operated poppet Valve construction Air/Inert gas Fluid Withstand pressure MPa 2.0 Body material Al Valve specifications Coil specifications Seal material HNBR Ambient temperature C 20 to 60 Fluid temperature C 10 to 60
Supply should be "1", the outputs 2'and "4', the pilot port connecting"l" with 2" is then "12" etc. Table 7.2 shows the tour main sets of port identifications in use. Preterred are now the numbers.
Cap AXT103-4 XT021-12 XT103-5 XT010-20 XT010-21 XT041-1 Resin Resin Bushing Spring Rubber plug for wire Round head combination screw Plug for cover r t y u i o Gasket XT013-31-2 NBR NXT030-8 !
VDC Pressure Characteristics Pressure Characteristics 1 i 6 _ 102 9 s 3 o t 5 o 1000 2000 3000 4000 5000 F ow rale f/min(ANBI 20 30 40 200 400 600 400 looo Fow rale i/m n(ANF) 1 3 1 102 e7 T3 d 7 3 58 a a a 29 1 5 1 5 o 4 8 1 2 1 6 2 A 2 4 2 8 400 800 1200 1.in 2004 2400 200 400 600 800 1000 Belief flo\i/ i.
How to Order VR 12 1 1 F 06 Body size Applicable tubing outside diameter Metric sizes Inch sizes 1 1/8 standard 3.2 23 04 06 01 03 07 1/8" 5/32" 1/4" 4 6 Use 1/8" tubing for 3.2.
SOmA Nil Relay, Sequence controller D-660 l00VAC Max.2SmA 200VAC Max. 12.SmA Model Load voltage Max. current or conduit range Indicator light Application D-A31 1 00VAC 2SmA Relay, Sequence controller 200VAC 12.SmA D-A37 24VOC S-30mA D-A39 24VDC 10-60mA Sequence controller DIN connector type D-A4 type Relay, Sequence controller Model Load voltage Max. current or conduit range Indicator
Note 2) When holding a workpiece close at the end of open/close stroke of fingers, detecting performance of the combinations listed in the above table may be limited, depending on the hysteresis of an auto switch, etc. 12-12-10 12-12-11
, 350, 400, 450, 500, 600, 700, 800 12-REA40 12-REA50 50 1300 Non-lube 200, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000 63 12-REA63 Note 1) Stroke exceeding the standard stroke but below the maximum manufacturable stroke is available as special orders.
Proper tightening torque Nm Tightening torque for piping (ftlb) Connection threads M5 1.5 to 2 (1.11 to 1.48) Rc 1/8 7 to 9 (5.16 to 6.64) Rc 1/4 12 to 14 (8.85 to 10.33) Rc 3/8 22 to 24 (16.23 to 17.70) Reference Tightening of M5 fitting threads After tightening by hand, tighten approximately 1/6 turn further with a tightening tool.
Burst pressure Note) Min. bending radius (mm) 24 Burst pressure (MPa) Operating temperature Material 20C to 60C Nylon 12 Note) The value at temp. of 20C and with O.D. variable rate 10% max.
An application which has the possibility of having negative effects on people, property, or animals, requiring special safety analysis. 12 Actuator Precautions 1 Series MGZ Be sure to read before handling. Precautions on Design Selection Warning Warning 1.
16 20 8 24 2 4 6 8 10 12 Discharge rate l/min Discharge rate l/min Selection from flow rate characteristic graphs (for PA3000) PA313 Air consumption 160 Required specification example: Find the pilot air pressure for a discharge rate of 4l/min and a total lifting range of 15m.
Recommended tightening torque Unit: Nm Connection thread 3/4 28 to 30 1/8 7 to 9 1/4 12 to 14 3/8 22 to 24 1/2 28 to 30 1 36 to 38 Torque 5-8-23
AV Flow rate (m3/min (ANR)) AU Inlet pressure 0.5 MPa AF Inlet pressure 0.4 MPa Piping AR Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com Warning IR If installing an air tank, install it upstream of the bypass oil feed adapter.
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com ZSP ISA2 IS ZSM PF2 IF Data Can be integrated with ZM ejector system.
16 20 8 24 2 4 6 8 10 12 Discharge rate l/min Discharge rate l/min Selection from flow rate characteristic graphs (for PA3000) PA313 Air consumption 160 Required specification example: Find the pilot air pressure for a discharge rate of 4l/min and a total lifting range of 15m.
16 20 8 24 2 4 6 8 10 12 Discharge rate l/min Discharge rate l/min Selection from flow rate characteristic graphs (for PA3000) PA313 Air consumption 160 Required specification example: Find the pilot air pressure for a discharge rate of 4l/min and a total lifting range of 15m.