Smooth Cylinder/Low Speed Cylinder Knuckle Pin L2 Material: Carbon steel (mm) Pivot Bracket (Order separately) Applicable bore (mm) Applicable retaining ring 20 25, 32 40 50, 63 80 100 L2 Dd9 m t d Part no.
L1 L2 L3 Thermal relay Refer to 5.2 for reset.
10 9 345 357 369 385 397 409 415 427 439 7 8 310.5 322.5 334.5 346.5 358.5 370.5 373.5 385.5 397.5 6 241.5 253.5 265.5 269.5 281.5 293.5 290.5 302.5 314.5 5 207 219 231 231 243 255 249 261 273 4 172.5 184.5 196.5 192.5 204.5 216.5 207.5 219.5 231.5 3 138 150 162 154 166 178 166 178 190 2 103.5 115.5 127.5 115.5 127.5 139.5 124.5 136.5 148.5 L1 L2 L3 L1 L2 L3 L1 L2 L3 276 288 300 308 320
Average speed of cylinder is obtained by dividing the full stroke time by the stroke.
10SW-L3 10SW-L1 10SW-L2 1/2 26 10-32 Swivel Tees Fibre Gasket Supplied 27 32 19 32 19 32 360 360 360 25/64 23/64 23/64 5/16 Hex Typ. 5/16 Hex 27 10SW-T2 10SW-T3 10SW-T1 Page 6 Distributed by Power Aire, Inc
Cuts air consumption by operating the return stroke at a reduced pressure.
Turn the manual override clockwise by 180 to set the E mark to "1" and press it in the direction indicated by arrow, then it will be locked in the ON state. Turn the manual override counterclockwise by 180 to set the E mark to "0", then it will be reset. Connection of Lead Wire (Not necessary if ordering pre-connected model.)
After replacing the coil, the clip is reinstalled by pushing it back in the direction opposite to its removal. 4.5-14
allows sequential switching operation, preventing blow by and air entrainment.
Symbol L1 L2 Calculation formula: L1 = 26n + 24, L2 = 26n + 12 Calculation formula: L1 = 26n + 36, L2 = 26n + 10 5-5-7 4 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 5-5-8 5 3 Port Air Operated Valve Series VTA315 How to Order SA VTA315 VA SA Port size Indicate
Cuts air consumption by operating the return stroke at a reduced pressure.
At that time, the lower poppet valve y opens by the degree preset by the needle !1. (Counterclockwise rotation of the needle opens the poppet valve.)The upper and lower poppet valves operate independently.
Products approved by CSA or UL standards are accepted in most states and governments beyond question.
The length of the cable between stations (L1, L2 ... Ln) must be 0.5 m or more. 2. The total cable length must be L1 + L2 ... + Ln 50. 3. Please connect terminating connector with PLC. When multiple DRIVERs are connected by MECHATROLINK-II communications cable, a terminating connector must be installed at the final DRIVER. 19 - 3.
Yaw moment M3 = W4 x L2 L2 Data YES Is there any influence of noise? (Refer to Caution on Handling on pages 6 and 7.) Install a noise filter.
Yaw moment M3 = W4 x L2 L2 YES Is there any influence of noise? (Refer to Caution on Handling on pages 6 and 7.) Install a noise filter.
Yaw moment M3 = W4 x L2 L2 Data YES Is there any influence of noise? (Refer to Caution on Handling on pages 6 and 7.) Install a noise filter.
Safe Vacuum self-holding function by means of double solenoid valves.
Right Left Right Left 112 (3.7) Vacuum (V) port (M5) Note 5) 21 10 Dimensions 1 2 3 4 5 6 7 8 (mm) n L1 L2 K J 5 6 Note 2) The above dimensions are for ZQ1000M2 .
Safe Vacuum self-holding function by means of double solenoid valves.