Series MXP Precision Air Slide Table Deflection on A when load is applied on F. Table deflection when yawing moment is applied. Deflection on A when load is applied on F. Table deflection when roll moment is applied. Deflection on A when load is applied on F.
N T, F, N are order made specifications.
N T, F, N are order made specifications.
Prevent contaminant's f rom entering fittinge and cartridges.
Double acting, Single rod Double acting, Double rod CE1 50 63 10, 15, 20, 25, 30, 35 40, 45, 50, 75, 100 CE2 80 100 ML2B C J G5-S CHQB CHQWB CV MVGQ CC For details, refer to the catalog CAT. E111.
The acquisition of waveform will be canceled with Stop button. 75 - 5.11.3 Operation Instruction When the PLC on the master side sends the operation command, the actuator will operate. When the trigger conditions in 5.11.1 (2) are satisfied, the operation waveforms can be captured.
(Crimping tool: Model DXT170-75-1) ZSE1-16, -17 ZSE1--16/-17 ZP Brown DC (+) OUT1 (white lead wire, red LED) can be set with pressure setting trimmer 1 (SET1). OUT2 (green lead wire, green LED) can be set with pressure setting trimmer 2 (SET2).
L1 L21 L3 M1 d2 M3 Q1 D22 2 x F VAC.
Mode 1: Allocation to the right f) Unit address from the end plate. order Mode 1/Mode 2 Mode 1 Available Mode 2: Allocation to the left from the wireless unit.
These vortexes are stable under certain conditions, and their frequency is proportional to the flow velocity, resulting in the following formula. f = k x v f: Frequency of vortexes, v: Flow velocity, k: Proportional constant (determined by the vortex generator's dimensions, shape, etc.) Therefore, the flow rate can be measured by detecting this frequency.
Max. 3.5 T N S M U D J Bracket (Option) AR20(K)-B to AR40(K)-06-B 2 x P1 Panel fitting dimensions A (Port size) Y W C B Q V K OUT OUT IN IN Z Plate thickness AR20(K)-B to AR30(K)-B: Max. 3.5 AR40(K)-B : Max. 5 R F P2 S (Pressure gauge port size) Bracket (Option) U M J D T N AR50(K)-B/AR60(K)-B 2 x P1 A (Port size) B Q C K OUT IN R F P2 S (Pressure gauge port size) Bracket (Option) T N J
QL 6 13.5 Prepared hole diameter 3.3 2-M3 x 0.5 (Plug: M-3P) 6 (fitting seat surface dimension) 170.05 M3 x 0.5 Vacuum suction port Stroke: S M 1 Mounting base side B D Piping port 2-M3 x 0.5 A 5 5.5 A 3.2 J 2.4 Z Section AA 3.5 Depth 2 2.5 +0.030 0 7 +0.030 0 Depth 2 2.5 Q QL 11-/22-MXPJ6-10 4M3 x 0.5 depth 3 F (mm) E F H J M Q QL S Z Model 23 25 38 27 37 28 8 5 44 11-/22-MXPJ6-51 30 35
TA DL2 TF TG A S + Stroke H NA F ZZ + Stroke Section TA With non-locking type manual override (suffix N) With locking type manual override (suffix L) HN HR MO RF WL WL KA 0.1 C 8-J NA (mm) Stroke range Bore size (mm) A AL B1 C D DL2 E F GA GB H H1 HR HN (max.)
110 { } 5 150 194 125 G1/2 Electric conduit 35 At accessory E: 195 At accessory F: 275 { } 4 x M8 x 1.25 depth12 (Female thread for rear mounting) With optional resin cable clamp Applicable cable O.
Refer to p.4.1-74, 4.1-75 for specifications and models.
40, 63, 100 Guide Table Series 10-MGF Air Preparation Equipment Pressure Control Equipment Flow Control Equipment Pressure Switches/ Pressure Sensors Directional Control Valves Air Grippers Modular F. R.
Center of rotation and center of gravity of the load are concentric. mg F L L mg Friction force is applied. Rotation shaft is vertical (up and down). 2 Ta = = t2 Ts = F L Gravity is applied in rotating direction.
: 2 m) Exhaust regeneration (ID20, 30) (mm) A B C D E Mounting dimension J H L K G F 240 240 320 320 Model Port size Nominal size (B) ID20 ID30 ID40 ID60 1 4 1 2 1 2 3 4 120 120 170 170 45 45 75 75 520 615 850 961 128.5 128.5 243.5 243.5 59.5 59.5 66.5 66.5 95 95 95 95 134.5 134.5 183 183 222 222 302 302 59.5 59.5 88 88 9 9 9 9 136 ID Series Specific Product Precautions Be sure to read this
75 71 Accessories Operation Manual (for installation/operation) 2 pcs.