Series MHR2 11- 2 Finger Rotary Actuated Air Gripper 22- Size: 10, 15, 20, 30 36 A Finger closing port Finger opening port M3 x 0.5 M3 x 0.5 10 Finger closing port M3 x 0.5 M3 x 0.5 25 25 Finger opening port 4 x M3 x 0.5 thread depth 6 M3 x 0.5 thread depth 4 35.5 (A, B common view) Vacuum suction port 0 12h9-0.043 +0.02 0 2 x 3 depth 6 (A, B common view) 1.5 Auto switch mounting groove 5 4.7 3.5 15.7 12 2-3 27 41.5 (45) 8 17 2 x 4.2 2 2 15.5 8-0.05 0 3.5-0.03 0 3.5
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Use the table as a guideline for mounting. Auto switch mounting bracket part no. BMG2-012 Auto switch part no. D-M9(V)/M9W(V)/M9A(V) Note) Use a screwdriver with a grip diameter of 5 to 6 mm to tighten the set screws (M2.5). The tightening torque should be 0.5 to 1 Nm. As a rule, it should be turned about 90 beyond the point at which tightening can be felt.
Do not apply a lateral load to the external slider. When a load is mounted directly to the cylinder, variations in the alignment of each shaft center cannot be offset, which results in the generation of a lateral load that can cause malfunction.
(2) Model d T Weight (g) H D1 D2 L1 L2 L3 L5 (1) A (2) D3 L4 Max.
(2) Model d T Weight (g) H D1 D2 L1 L2 L3 L5 (1) A (2) D3 L4 Max.
(2) Model d T Weight (g) H D1 D2 L1 L2 L3 L5 (1) A (2) D3 L4 Max.
Exhaust center: A, B R1, R2, Pressure center P A, B 3 position closed center 3 position exhaust center Specifications 2 position double 2 position single Fluid Air 0.15 to 0.9 0.1 to 0.9 Operating pressure range (MPa) 3 position pressure center 3 position 0.15 to 0.9 Pilot pressure range (MPa) 2 position double 2 position single (0.4 X P+0.1) to 0.9 P: Operating pressure 0.1 to 0.9 3 position
Connector location on U side (FU) 3.5 163 10.7 47 106 71.7 9 9 U side 27 Manual override n X 12 12 2 B 4 A 8 2 B 4 A A A B A B A B A B A B A 7 SMC SMC SMC SMC SMC SMC SMC A A A A A A A B B B 2 B 4 A Indicator light 6 2 B 4 A 5 L2 L1 2 B 4 A 4 B B 2 B 4 A 3 2 B 4 A 2 P = 25 2 B 4 A 1 50.5 44 X Stations 38 27 Connector location on D side (FD) 11.7 16.2 139.9 (Single) 43.2 49.7 D side 148.9
Plug that A port to avoid mistaking B port for the A port.
Connector A terminal no. B-1 A-1 B-2 A-2 B-3 A-3 Circuit Cable color Brown Red Orange Yellow Green Blue A A B B COM-A/COM COM-B/ 2 1 6 5 3 4 Cable color Connector D terminal no.
VXD2 Z 1A VXD2 Z 3 0 A A VXK Enter standard product number.
A Unused A Unused A Unused A Unused A Unused A B A B A B A B A B A A A B A B A B A A A A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 6 7 8 9 10 11 12 13 14 15 0 0 1 2 3 4 5 Type SC OMRON Corporation SYSBUS Wire System Type SD SHARP Corporation Satellite I/O Link System ADDRESS NO. STATION NO.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
When a load, such as a relay or solenoid valve, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.
A ARP w y IR-A IR r IRV i VEX SRH !
Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.