Compact ao . , , , , t o o 3 . , , . , 05 stePping a ''.a: ' , . a , : a : l r : : i : l ::: I iob' ' ', ' t99;:9i1':i1:t t: llli,2.gtepping O8: 12mm lead , , . , , 1 ( } . u 5 asbinriea,i : r iri llliqq'i'' o5 stepoinq 30 08; zmm lead o2 stepping 80 08; 5mm lead 10.03 30 08; 2mm lead s5 stepping 80 08; 5mm lead a I a a a 100 O8; 6mm lead o2 stepping 200 08; 12mm lead 10.05 I M <-iD;;,;; uo100 08
Never mount a product in a location that will be used as a foothold. The product may be damaged if excessive force is applied by stepping or climbing onto it. Do not use this cylinder as a stopper. Minimum adjusting stroke necessary for a positioning stop is 5mm. Operate for 5mm or more before a positioning stop. Ex: 1.
ARJ AR425 to 935 Air-operated type Pilot pressure VBA11A VBA10A, 20A, 40A, 43A ARX Drive chamber A Governor Drive chamber A Governor Drive chamber B Booster chamber A AMR IN (Inlet) IN (Inlet) Drive chamber B ARM VBA22A, 42A Piston rod Piston rod ARP Booster chamber A IR-A Piston Piston IR Check valve Booster chamber B Booster chamber B Check valve IRV Switching valve Switching valve E OUT
Therefore, do not use a cylinder without a bumper bolt. Furthermore, if the bumper bolt is tightened without a nut, the piston seal is caught in the leveled part, damaging the seal. 3. A bumper at the end of the bumper bolt is replaceable. In case a missing bumper, or a bumper has a permanent settling, use a following part numbers for ordering.
Caution : CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning : WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger : DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Never mount the product in a place that will be used as a scaffold during piping.
X Tank capacity 1000 Relief time that is read t = 2000 1000 = X 23 = 46 The result is 46S. From the above, the relief time is 263=23S 5.1-5 VEX1 Construction/Operation Principles/Component Parts [1] When A port pressure is high. [3] When A port pressure is low.
(Normally closed) A N.O.
When a 3 port valve is mounted on a 5 port manifold, the A port is the working port. The B port can either be plugged or unplugged.
B 220V Dryer Capacity Model A Part No.
] R P R 63.8 (DIN 65.1) 63 (DIN 64.3) R P R B B B B B 122 [126.4] 19 19 19 60 31.5 22 A A A A A 1/4 (P, R port) 13.8 (For DIN: 15.1) 4-4.5 (For mounting) (Pitch) P = 20 29 Manual override (Station n) (Station 1) (Light/surge voltage suppressor) + + + 73 [80] 57.6 A A 10.5 41 30.5 B B 6.5 (Pitch) P = 20 25 1/8 (A, B port) L plug connector (L) M plug connector (M) DIN terminal (D) M8 connector
10.5 [5m ] L E C P *B* (a) (b) 2 A B-1 L 1 A A-1 (b) 6 A B-1 B B-2 1 1.5m 5 A A-1 B A-2 3 3 3m B B-2 COM-A/COM B-3 4 B A-2 COM-B/A-3 5 5m (c) COM-A/COM B-3 Shield COM-B/ A-3 Vcc B-4 12 GND A-4 13 Vcc B-4 A B-5 7 GND A-4 A A-5 6 A B-5 B B-6 9 A A-5 S B A-6 8 (d) B B-6 3 B A-6 (a) + B-1 4 A-1 5 + B-3 1 2 A-3 (a) (8) (14.2) B1 A1 (b) 2 1 (17.7) (14) (18) (10.2) 6
11.5 46.5 D-F7V D-J79C D-F7 D-J79 D-A9 D-A9V D-F9W D-F9WV D-M9V D-M9 D-A79W D-A72 D-A73 D-A80 D-F9BAL D-P5DWL D-P5DWSC Model A 8.5 43.5 A 11 46 A 13 48 B CKQ CLKQ B B B B B B A 14 49 B B A 14 49 B A 14 49 B A 7 42 A 10 45 A 11.5 46.5 A 11 46 19 or more 17 or more 33 or more 27 or more 28 or more 27 or more 22 or more 30 or more 22 or more 17 or more 54 or more 52 or more Auto Switch Mounting
MS-DOS is a registered trade mark of Microsoft Corporation. Pentium is a trade mark of Intel Corporation.
Air filter (5m or less) When using a solenoid valve, use a metal seal type (series VQ, VQZ, SQ, etc.).
Thus, in spite of using pneumatic equipment, it performs similarly to a RE A B REC CX CY MQQ M A selection of valve unit is available to suit your application. High cylinder driving speed.
Dont use a wrench on push-to-connect end. 2 2 Cut tubing square with a clean 90 edge Dont use excessive tube angle cut which can lead to leakage or breaking. 90 90 3 3 Use SMC Tube Cutters Dont use dikes, a knife, a saw or a dull tool to cut the tubing.
)MXQ6B MXQ6(C) Nm MXQ6(A) RJ0603 0.85 MXQ8(A,C) MXQ6B RJ0603 0.85 MXQ12(A,C) MXQ8B RJ0805 1.67 MXQ16(A) MXQ12B RJ1006 3.14 MXQ20(A) MXQ16B RJ1007H 3.14 MXQ25(A) MXQ20B RH1410 10.8 12 2-8 kg RJ MXQ6(A) 0.6 0.6 0.6 MXQ8(A,C) 1 1 1 1 MXQ12(A,C) 2 2 2 1 MXQ16(A) 4 4 4 2.5 MXQ20(A) 6 6 6 5 MXQ25(A) 9 9 9 5.5 2 45 3 , , 13 OFF MXQ6(A) 2.85 5.65 MXQ8(A,C) 2.4 5.6 MXQ12(A,C) 4 5.5 MXQ16(A) 5