Round Type Low Pressure Hydraulic Cylinder Series CHM H G I J K L A B C D E F M R Size Tolerance +0.058 0 -0.1 -0.2 -0.1 -0.2 -0.1 -0.3 -0.1 -0.3 AD-FI-20 AD-FI-25 AD-FI-32 AD-FI-40 +0.027 0 +0.027 0 +0.027 0 +0.027 0 9 9 16 16 36 38 55 55 16 18 22 22 9 9 12 12 20 25 32 40 10 10 15.5 15.5 20 20 24 24 14 14 20 20 M8 x 1.25 M10 x 1.25 M14 x 1.5 M16 x 1.5 20 25 32 40 46 46 56 64 28 30 40 43 60 60 80 88 22 22 30 30 16 16 16 24 10 10 12 12 30 30
How to manually change from an unlocked state to a locked state To change from an unlocked state to a locked state: Unlike the procedure for manually disengaging the lock, never rotate the pin by striking it, as it could bend or damage the pin. The lock is disengaged at the time of shipment.
The unit body can be fixed by tightening four holding bolts evenly at an arbitrary position. However, there is a possibility that the adjustment mechanism will be tilted due to high impact energy. Since the holder mounting bracket for adjustment is available as an option for -X416, -X417, we recommend that you use it.
Rod end thread type is an optional product. (Refer to page 281).
Please contact SMC if hysteresis causes an operational problem.
solid state auto switch is available after receiving an order. 18
Do not use the air cylinder as an air-hydro cylinder. The use of turbine oil as a fluid for an air cylinder may result in oil leakage. 4. The oil stuck to the cylinder is grease. 5. The base oil of the grease may seep out.
With air cushion FT F 4 x FD 0 E0.05 FX0.15 B B FX0.15 (mm) Bore size 40 B 61 E 25 F 2 FX 46 FD 6.6 FT 8 50 63 76 92 30 32 2 2 58 70 9 11 9 9 Note) End boss is machined on the flange for E. Other dimensions are the same as basic type.
Some fluids can deteriorate a seal or an O-ring, and have an affect on the filter function, causing leakage. The wetted parts of the pressure gauge is made of brass. Check the compatibility with fluid in use. EB ES 1. Failure to observe the procedure will likely cause fluid leakage or removal of a cover, which may lead to an unexpected accident.
An application which could have negative effects on people, property, or animals Compliance Requirements requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for 1.
(Assuming approximately 30% dispersion) There may be the case it will vary substantially depending on an ambient environment.
Also, BBA2 is included when an auto switch alone is shipped.
Refer to page 100 for part numbers. 45 46 Non-standard Motor Series LJ1H10 Rolled Ball Screw High Rigidity Direct Acting Guide Motor Output 50W 12mm/12mm lead Horizontal Mount How to Order Stroke 1 LJ1H10 G NB 1 F W X10 Cable entry direction Top entry Left entry Power supply voltage Motor specification Cable entry direction Switch Matsushita Electric Industrial Co., Ltd.
When you begin to feel that the screw is being tightened, turn it an additional 90.
Never remove valve at an angle.
Furthermore, by connecting an input block, a maximum 32 sensor signal inputs are possible. SI unit for AS-i As a AS-i slave unit, this kit is capable of up to 4 or 8 points of solenoid valve ON and OFF control. Furthermore, by connecting an inmput block, a maximun 4 or 8 sensor signal inputs are possible.
When an offset load is expected, provide a suitable mechanism such as a floating joint. 2) Use clean air (atmospheric pressure dew point temperature 10C or less). Use of a series AM mist separator (filtration rating of 0.3 m or less), or series AM + AMD (filtration rating of 0.01 m or less) is recommended.
Non-locking push type [Standard type] Push in the direction of an arrow.