SMC Corporation of America
Elite Part Number Search
Search Results "VV2Q22-14-DO-00N"

SET To measuring mode 16-3-14 14 Series PSE530/200 Multi-channel Controller/Pressure Sensor Operation 3: Special Setting 1 Precision indicator setting Refer to A Display calibration function on page 16-3-17 for details. Calibration mode + SET MPa Measuring mode kPa Press and hold for 2 seconds or longer.

(between lead wire and case) Ambient temperature ... 10 to 60C (14 to 140F) Enclosure . IEC529 standard IP67, watertight (JISC0920) Weight Table Unit: g (oz.)

An injury or failure can result. 3 Display LED LED display to indicate the input unit status. 128 inputs/128 outputs Number of points Sensor connector Connector for sensor. 4 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. No.

T-slots l Model Bolt Max. tightening torque Nm Max. screw-in depth (l mm) LXP M5 x 0.8 7.4 8.5 Use bolts at least 0.5mm shorter than the maximum screw-in depth, so they do not touch the body.

Refer to pages 14-21-3 to 14-21-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 14-14-6 to 14-14-8 for precautions on every series. Suffix Basic size (Applicable compressor rating) T With terminal (Provided as standard for HAA37.)

Do not disassemble the product or make any modifications, including additional machining. 6. Do not use tools such as pliers to rotate the knob. AS-T It can cause idle rotation of the knob or damage. It may cause human injury and/or an accident. ASP 7. Verify the air flow direction. 4. The flow rate characteristics for each product are representative values.

Do not disassemble the product or make any modifications, including additional machining. 6. Do not use tools such as pliers to rotate the knob. AS-T It can cause idle rotation of the knob or damage. It may cause human injury and/or an accident. ASP 7. Verify the air flow direction. 4. The flow rate characteristics for each product are representative values.

(Do not change.) Pin 3 Reserved. (Do not change.) OFF Pin 4 Reserved. (Do not change.) OFF When using the MECHATROLINK-III standard servo profile, set the number of transmission bytes to either 32 or 48. When using the MECHATROLINK-II-compatible profile, set the number of transmission bytes to either 16 or 32.

Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water, or where there is direct contact with same. 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5.

RHC Nil Without auto switch (Built-in magnet) Stroke MK(2) For the applicable auto switch model, refer to page 10-3-14.

Do not excessively expand or bend the bracket as it may break. The appropriate tightening torque for the standard bracket is shown below.

RHC Nil Without auto switch (Built-in magnet) Stroke MK(2) For the applicable auto switch model, refer to page 10-3-14.

18.5 23.5 Proper Mounting Position (mm) a b 14 18 17 c 20 24 23 d D-A9 type D-M9 type D-F9 W type 2 6 5 8 12 11 In order that adjacent switches do not misoperate, they should be set within 1 mm of the proper mounting positions indicated in the table above.

Do not connect multiple NFC readers / writers to a PC. Connection details using the I/O Configurator for NFC and wireless unit To use a wireless system, it is necessary to "pair" a Wireless Base and Remote. Configure this using the I/O Configurator (NFC version).

Actuator side (14) (18) A1 B1 (17.7) A 10*1 (13.5) B 15*1 A6 B6 1 2 C 20*1 Connector D (14.7) 15 16 Connector A (30.7) L (11) (10) *1 Produced upon receipt of order (Robotic cable only) Cable color Connector C terminal no. Brown 2 Red 1 Orange 6 Yellow 5 Green 3 Blue 4 Signal Connector A terminal no.

Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not operate in locations where vibration or impact occurs. 3. In locations which receive direct sunlight, provide a protective cover, etc. 4. In locations near heat sources, block off any radiated heat. 5.

Do not operate or set with wet hands. This may lead to an electric shock. End plate bracket (EX600-ZMA2) SUPPLIERS DECLARATION OF CONFORMITY Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Connector (Base only) (2) Add more units.

Do not collide the pallet while the lever is standing erect. For the lever with built-in shock absorber, do not collide the next pallet while the lever is standing erect. Otherwise, all energy will be applied to the cylinder body. 2.

Do not use in explosive atmospheres. 11. Do not use in locations where radiated heat will be received from nearby heat sources. 12. Ensure sufficient space for maintenance activities. When installing the products, allow access for maintenance and inspection. 13. Fluid pressure range Fluid pressure should be within the allowable pressure range. 14.