HRX-OM-Y098 For a facility with a large installation area that can vent the air naturally: Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility with a small installation area that can not vent the air naturally: Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
For a facility having a large installation area (that can vent the air naturally): Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level.
For a facility having a large installation area (that can vent the air naturally): Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
14 A Current consumption 5 A (100 V) to 2.5 A (240 V) 9 A (100 V) to 4 A (240 V) 10 A (100 V) to 4 A (240 V) 8 A (200 V) Power consumption 440 W*1 850 W*1 900 W*2 1500 W*2 Alarm Refer to Alarm.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
ion (SO42) [mg/L] 50 or less v Acid consumption amount (at pH4.8) [mg/L] 50 or less v Total hardness [mg/L] 70 or less v Calcium hardness (CaCO3) [mg/L] 50 or less v Ionic state silica (SiO2) [mg/L] 30 or less v Standard item dV dt = Voltage increase ratio dV Iron (Fe) [mg/L] 0.3 or less v v Copper (Cu) [mg/L] 0.1 or less v Sulfide ion (S2) [mg/L] Should not be detected. v Ammonium ion (
x Depth 580 HRSE018-A-23 HRSE024-A-23 HRSE012-A-23-T 48 Height 790 x Width 470 x Depth 580 HRSE018-A-23-T HRSE024-A-23-T IDH Selection Warning 1.
MX A 3.0 25 L MTS A 5.0 32 L MY A 12 40 L CY A 12 50 L MG A 24 63 L CX Adjusting bolt lock nut Unit holding bolt
The shock absorber should be replaced as a spare part if a deline in the energy absorption capacity is observed. Refer to the table below about how to order a replacement shock absorber. MTS MY CY Bore size (mm) 10 15 25 No. MG RB0805-X552 RB1006-X552 CX 2.
(mm) At the minimum stroke of 25 mm adjustment bolt Basic stroke At maximum stroke adjustment At the minimum stroke of standard adjustment bolt Bore size (mm) Adjustment bolt fixing bolts Tightening torque Adjustment width across flats Bore size (mm) 10 15 25 10 15 25 A 2 A 26 A = 0.8 A = 0.6 A 0 4 M3 1.0 to 1.3 Nm A 2 A 26 5 M5 4.6 to 6.2 Nm Adjuster holder Adjuster holder A Adjustment
) [mg/L] 50 or less p Standard item Acid consumption amount (at pH4.8) [mg/L] 50 or less p Total hardness [mg/L] 70 or less p Calcium hardness (CaCO3) [mg/L] 50 or less p Ionic state silica (SiO2) [mg/L] 30 or less p Iron (Fe) [mg/L] 0.3 or less p p Copper (Cu) [mg/L] 0.1 or less p Sulfide ion (S2) [mg/L] Should not be detected. p Ammonium ion (NH4+) [mg/L] 0.1 or less p Residual chlorine
The mounting pitch of cylinders should be at least the values given in the table below. 8 12 to 40 MX Mounting style (1) Mounting style (2) Mounting style (1) Mounting style (2) Cylinder A Auto switch position Cylinder B Cylinder A Auto switch position Cylinder B MTS Cylinder A Cylinder B Cylinder A Cylinder B Auto switch position Auto switch position MY CY d d L L MG Courtesy of Steven Engineering
drain cock C2SL-36-A With bowl guard C2SL-36C-A C3SL-36-A C4SL-36-A Nylon Drain cock with barb fitting With bowl guard C3SL-36W-A C4SL-36W-A Metal Without drain cock C2SL-2-A C3SL-2-A C4SL-2-A With level gauge C3LL-8-A C4LL-8-A With drain cock C2SL-23-A C3SL-23-A C4SL-23-A With level gauge C3LL-38-A C4LL-38-A *1 The bowl assembly comes with a bowl seal.
1 @3 @5 o A @4 A A-A !4 @2 @0 !0 w !3 @6 Component Parts No.