This is a legacy product. Please contact us for the latest version.sales@ocaire.com NEW SY3000 MFLD. MANIFOLD. VALVE. NEW SY3000 MFLD, FITTING LESS THAN 1/4. 1.70857 lb. UP.
SMC has improved product performance and reliability with the redesigned SY series valve. The SY3000 and SY5000 have the same valve width as their predecessors, but the flow has been increased by up to 80%, allowing the valve size to be reduced. A built-in strainer in the pilot valve prevents trouble caused by foreign matter. By using H-NBR seal material for the main valve and seals, Ozone
SMC has improved product performance and reliability with the redesigned SY series valve. The SY3000 and SY5000 have the same valve width as their predecessors, but the flow has been increased by up to 80%, allowing the valve size to be reduced. A built-in strainer in the pilot valve prevents trouble caused by foreign matter. By using H-NBR seal material for the main valve and seals, Ozone
SMC has improved product performance and reliability with the redesigned SY series valve. The SY3000 and SY5000 have the same valve width as their predecessors, but the flow has been increased by up to 80%, allowing the valve size to be reduced. A built-in strainer in the pilot valve prevents trouble caused by foreign matter. By using H-NBR seal material for the main valve and seals, Ozone
Lightweight, compact, and precision control make these speed controls the right choice for many heavy-duty applications. These speed controls are offered with in-line and elbow construction to give the widest choice to your unique application. Locking nuts are included as standard as well as simplified mounting. Thread sizes range from M3 to 2 and are available in both inch (NPT) and metric
This is a legacy product. Please contact us for the latest version.sales@ocaire.com, MANIFOLD, VALVE, NEW SY5000 MFLD, UM, NEW SY5000 MFLD, FITTING 3.30693 lb, 3.30693 lb
Lightweight, compact, and precision control make these speed controls the right choice for many heavy-duty applications. These speed controls are offered with in-line and elbow construction to give the widest choice to your unique application. Locking nuts are included as standard as well as simplified mounting. Thread sizes range from M3 to 2 and are available in both inch (NPT) and metric
I/O Configurator (NFC version) Setting range: 0.1/0.2/0.5/1/2/5/10/30/60 s (Initial value 1 s) The analogue input update time is set for every wireless slave unit. Analogue input update time Define the address assignment direction of the EX600 I/O units connected to the wireless master unit. The address assignment direction is changed by mode 1/mode 2. Be careful about the I/O map.
Setting range: 0.1/0.2/0.5/1/2/5/10/30/60 s (Initial value 1 s) The analogue input update time is set for every wireless slave unit. Analogue input update time Define the address assignment direction of the EX600 I/O units connected to the wireless master unit. The address assignment direction is changed by mode 1/mode 2. Be careful about the I/O map.
[F90] Setting of all functions completed : Setting of each function Every time the SET button is pressed, the display moves to the next function in order of "Setting of each function" on page 60. Set by using the UP and DOWN buttons.
(increment of 1 sec.), 20 sec., 30 sec., 40 sec., 50 sec. and 60 sec.
The slant angle of each rope should be 60 degrees or less. Never lay the product on its side. The compressor oil will leak in to the refrigerant piping, which may cause early failure of the compressor. Drain the residual fluid from the piping as much as possible to prevent any spillage.
Thermostat working temp. : 60+/-5 C (at radiating water side) Thermostat ERR14 Alarm 90+/-5 C (at recirculating fluid side) After alarm occurrence : The unit (temp. control, pump) stop.
VXF21A VXF22A VXF23A VXF24A VXF27B VXF28B VXF25(A,B) VXF26(A,B, C,D) Product number Orifice size mm 22 28 44 53 70 80 90 100 Air Fluid Minimum operating pressure Maximum operating pressure MPa 0.03 0.1 MPa 0.7 Fluid temperature -10 (Non-freezing) to 60 Ambient temperature -10 to 60 Coil insulation type Class B Enclosure IP65 Alloable voltage fiuctuation 10% of rated voltage AC VA 10 7
Operation/ Shutdown Fig 3.8 Timing chart of signals Reset a counter of Abnormal stop 10 min Abnormal stop 4 (1) The abnormal stop will be automatically reset until 4 times within 60 minutes, but the 5th time will not be automatically reset in this case, reset Automatic return 60 min Abnormal stop 3 Abnormal stop 2 Abnormal stop 1 Manual Abnormal stop 5 (2) When the alarm is generated by the
.* Standard dew point -60oC : about 60 min.* * This time can be shortened as described below. 1) Provide a valve on the outlet side of the membrane air dryer. 2) Supply air with the valve closed so that only purge air flows through the membrane air dryer. 3) After 15 minutes or more, open the valve and let air flow to the outlet side equipment. Selection Caution a.
), ACMA (Australia/New Zealand), IMDA (Singapore), SIRIM (Malaysia), ENACOM (Argentine), ICASA (South Africa), NCT (Philippines), FAC (Russia), CoC (Ukraine), ANRT (Morocco) -67No.EX-OMU0028-D Models EX600-WSV1 EX600-WSV2 Enclosure rating Conforms to IP67 (with manifold assembled) Ambient temperature (Operating temperature) -10 to +50 oC Ambient temperature (storage temperature) -20 to +60
Order 42 Summary of Product parts 42 Mounting and Installation 43 Installation 43 Separate power supply 46 LED Display and Settings 47 Specification 48 Specifications 48 Dimensions 49 1 No.EX-OMS0014-A Input unit Model Indication and How to Order 50 Summary of Product parts 50 Mounting and Installation 51 Installation 51 Wiring 52 LED Display 58 Specification 59 Specifications 59 Dimensions 60
), ACMA (Australia/New Zealand), IMDA (Singapore), SIRIM (Malaysia), ENACOM (Argentine), ICASA (South Africa), NCT (Philippines), FAC (Russia), CoC (Ukraine), ANRT (Morocco) -78No.EX-OMW0006-D Models EX600-WSV1 EX600-WSV2 Enclosure rating Conforms to IP67 (with manifold assembled) Ambient temperature (Operating temperature) -10 to +50 oC Ambient temperature (storage temperature) -20 to +60
Model Motor size Set value of pushing force[%] LEPY6 LEPS6 Basic 70 to 100% LEPY10 LEPS10 Basic 50 to 100% Compact 60 to 100% 43 - a. Posn failed alarm is generated The product cannot reach a pushing start position due to variation in the width of workpieces. b. Pushing ALM alarm is generated The product is pushed back from a pushing start position after starting to push. c.