CEU1 CEU1P-D 3 (DIN ) LCD() 5 (-9.9.9) () E 2ROM(6.5 :FL) 90 20kHz RS10ms () DC10.813.2V60mA 100ms NPN PNP NPN PNP Max DC30V 50mA Max DC30V 50mA Max DC30V 50mA Max DC30V 50mA AC80120V50/60 z DC21.626.4V 10VA 5W AC1500V1 AC500V 1 DC500V50 0+50 3585RH 1500V600V Hz 2 10G XYZ 3 250g 6 6 6 6 6 6 6 6-1 1 1 1 (DC12V60mA) B A G N D A B COM RS COM COM 12V G N D A B COM OUT1
See the table below Belt tension Size Belt N Part number Bolts LEF25 LE-D-6-2 19.6 pull LEF32 LE-D-6-3 49.0 LEF40 LE-D-6-4 98.1 4. "Pulley plate" is installed. Bolts Size Tightening torque (Nm) M3 0.6310% M4 1.510% M5 310% 8.Troubleshooting When a fault occurs during the operation, the corresponding alarm or warning is displayed.
Operation/ Shutdown 3.10.6 PID manual setting CH1 PID (control parameter) P Proportion band (050) i Integral time (051) d Derivative time (052) PID(proportion band / integral time / derivative time) is manually set. [ Setting range] P: 0.1 to 999.9 I: 0 to 3200 sec. D: 0.0 to 999.9 sec. PID values are automatically set by auto tuning.
Channel number D Diagnostic Function of EX600 to self monitor if error has occurred or configuration has changed. E Error log A chronological list of previous errors occurred. A maximum of 30 errors can be recorded. Enforced output function A function to drive an output signal forcibly, ignoring control data from the PLC.
(example: If the Pressure switch with output impedance of 1k is connected to the A/D converter to detect the analogue output of 5V, the detected voltage by the A/D converter becomes 5(V) 1(M)/(1(k) + 1(M)) 4.995(V), and there is an error of approximate 0.005 V). Output impedance Output type The operation type of the switch output.
Speed Speed Acceleration Deceleration Position In pos ON INP output ON OFF -17-
Refer to the table below for accessory/option combinations Thread Rc (PT) Table: Accessory/Option combinations Depending on model l Not available Available F G (PF) N NPT Accessories Options C C D -J -R D J T AMD150 R AMD250 AMD350 AMD450 Applicable models Accessories /Options Port size AMD550 AMD650 AMD850 01 B B 06 10 14 1 8 3 4 1B N.C. auto drain N.O. auto drain Drain guide 1/4B IN R
Printed in Japan. 1st printing May, 2002 D-DAD P-80 (YG) This catalog is printed on recycled paper with concern for the global environment.
A A B C D E F A B C D A B C D A B C D A B C D Tubing O.D. PA 1 2 1 2 3 4 1 2 3 4 5 6 1 2 3 4 1 2 3 4 1 2 3 4 1/8" 1/8" PAX 1/8" 1/8" PB 1/4" 1/4" 1/4" 1/4" 3/8" 3/8" 3/8" 3/8" 1/2" 1/2" 1/2" 1/2" 3/4" 3/4" 3/4" 3/4" 1" 1" Note) For each body class, the second and later numbers or symbols indicate reducing.
Consult with SMC regarding water resistant types with the above model numbers. * Solid state auto switches marked with are produced upon receipt of order. ** Since D-A9and D-A9V cannot be mounted on 50, use of D-Z7 or D-Z80 is recommended. * Lead wire length symbols: 0.5 m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ D* Since there are other applicable
You do not need to specify "N" (i.e., without lead wire) for D-A3, D-A44, D-G39, and D-K39. This is the only standard specification automatically available for these models. D-A9V, M9V, M9WV, and M9A(V) models cannot be mounted on 25 to 40. Since there are applicable auto switches other than listed, refer to page 310 for details.
Nil S n 21 22 Relief type Vacuum suction type Auto switch D-A93 D-M9N, D-M9B Reed switch Solid state Action D Double acting The minimum stroke for auto switch mounting and operating range are the same as standard products.
Choice of output types: PNP, NPN How to Order D-M9PJ J M9 N L D Lead wire length Output specifications Symbol Specication L Between the sensor and amplier: 3 m, Amplier section: 3 m Symbol Specication N NPN output P PNP output Z Between the sensor and amplier: 5 m, Amplier section: 3 m D-M9NJ Dimensions [mm] Auto Switch Specications Indicator light D-M9NJ, D-M9PJ (With indicator light) Auto
D 16 inputs M12 connector (5 pins) 8 pcs. E 16 inputs D-sub connector (25 pins) F 16 inputs Spring type terminal block (32 pins) For specications, refer to the Fieldbus system EX600 series in the Web Catalog.
Use a D-class ground connection (ground with a resistance of less than 100). The cross sectional area of the grounding cable shall be 2 mm2 or more. The Grounding point should be as near as possible to the controller. Keep the grounding cable as short as possible.
Description Part No. (7) Element service indicator AM-SA072 (9) Drain port spacer AM-SA075 (4) (10) Auto drain Note1 (Including drain cock) Thread type Rc, G: AD43PA-D Thread type NPT : NAD43PA-D Note1) Auto drain (MAX.1.6MPa) cannot be replaced. Note2) All rubber materials are NBR. -15- Doc. no. AMX-OMU0058-C 6.
x n +4 x (n -1) -57No.PS-OMM0002CN-F A B C D E 4 OFF F SMC URL http://www.smcworld.com 2008-2014 SMC Corporation All Rights Reserved No.PS-OMM0002CN-F
Series