The number of the switches: N/A, Type of Auto Switch Mounting: Rail mounting, Head Cover Port Position: 90° to axis, Pivot Bracket: Without bracket, Rod End Bracket: Without bracket, Type of Mount Support: Basic type, Custom-made Specifications: None, Lock unit magnet: Built-in magnet
Table of Contents M9 M9V F9W(V) B Electrical entry is in the direction C (mm) Proper mounting position Proper mounting position Proper mounting position D-M9 D-F9W D-M9V D-F9WV D-M9 D-F9W D-M9V D-F9WV D-M9 D-F9W D-M9V D-F9WV Model Model Model A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C
B A B A B A B C D Normally closed (NC = b contact), solid state switch (D-F9G/F9H type) are also available.
Example) -M9NL Symbol Nil A B C Quantity Without auto switch 2 pcs. 1 pc. 1 pc.
9200-www.stevenengineering.com When tightening an auto switch mounting screw, use a watchmakers screwdriver with a grip diameter of 5 to 6 mm.
A model should be selected with a gripping force of 7 to 14 times that of the component weight. If high acceleration, deceleration or impact forces are encountered during motion, a further margin of safety should be considered.
Magnet: Built-in Magnet, Series: J2K, Mounting: Basic, Bore Size: 16mm, Stroke: 200mm, Head Cover Port Location: Perpendicular to Axis, Pivot Bracket: None, Rod End Bracket: None, Auto Switch: M9P--Solid State, Gen. Purpose, 3 Wire PNP, Horizontal, Lead Wire or Prewired Connector: 3m, Number: 2 pcs. (Or None in the Case of No Switch), Auto Switch Mounting Type: Rail Mounting
(Or None in the Case of No Switch), Auto Switch Mounting Type: A (Rail Mounting)
To connect a drain discharge pipe, use a pipe with a minimum bore of 10, and a maximum length of 5 m. Avoid using a riser pipe.
Due to a pressure fluctuation that occurs during the switching of the adsorption cylinders, the small particles of the adsorption agent could splash to the outlet side. Install a mist separator or a micro mist separator on the outlet side according to the application. 4. When installing a regulator, install it on the outlet side of the heatless air dryer.
Due to a pressure fluctuation that occurs during the switching of the adsorption cylinders, the small particles of the adsorption agent could splash to the outlet side. Install a mist separator or a micromist separator on the outlet side according to the application. 4. When installing a regulator, install it on the outlet side of the heatless air dryer.
ID-200Z ID-300Z ID-400Z ID-600Z 15.4 18.7 40.8 55.1 A B C inch mm inch mm inch mm 120 120 170 170 Operation Principles Provides dry air at dew point as low as 58F (50C).
This is a legacy product, and replaced byCDG1RN25-200Z CG/CG3 ROUND BODY CYLINDER. CYL, 25MM, DIR MT, AUTO-SW. ACTUATOR. 25MM CG DBL-ACT AUTO-SW. 1.52436 lb. IE.
This is a legacy product, and replaced byMB1B100-200Z MB TIE-ROD CYLINDER. CYL, TIE ROD. ACTUATOR. 100MM MB DOUBLE-ACTING. 15.60872 lb. SD.
This is a legacy product, and replaced byCDG1BN20-200Z-XB13, CYL, AIR, DBL ACT, LO SPEED, ACTUATOR, CG/CG3 ROUND BODY CYLINDER, HC, 20MM CG OTHERS (COMBO), .66138 lb
This is a legacy product, and replaced byCY1SG15-200Z, CYL, RODLESS, SLIDER, SW CAP, ACTUATOR, CY1S GUIDED CYLINDER, GM, 15MM CY1S SLIDE BEARING, 3.31105 lb
This is a legacy product, and replaced byCY1SG32-200Z, CYL, RODLESS, SLIDER, SW CAP, ACTUATOR, CY1S GUIDED CYLINDER, LM, 32MM CY1S SLIDE BEARING, 11.07073 lb
This is a legacy product, and replaced byMGPM25-200Z-XC4AW, "COMPACT, MGP, GUIDED CYLINDER, N lb
This is a legacy product, and replaced byCM2KB20-200Z, CYL, ROUND BODY, NON ROTATING, ACTUATOR, CM2/CM3 ROUND BODY CYLINDER, HK, 20MM CM2 NON-ROTATING, 0.79425 lb
This is a legacy product, and replaced byCDG1TA50-200Z-B54L-XC4, CYL, AIR, DBL ACT, ACTUATOR, CG/CG3 ROUND BODY CYLINDER, NE, 50MM CG DBL-ACT AUTO-SW, 5.41832 lb