Rotary Table/ 3 w @4 @3 !6 !7 !8 !1 @1 !2 q @0 u !
As a rule when W + Pa>PA adjust P so that W + Pa = PA. (2) Installing a regulator with check valve at position (b) can decrease lurching during descent and actuation delay during ascent. As a rule adjust P so that W + PA = Pa.
Magnet: D (Built-in), Type: Pneumatic, Mounting: D (Double Clevis), Bore: 20mm, Port Thread: Rc, Stroke: 50mm, Cushion: Rubber Bumper, Rod End Thread: Male Rod End, Rod Boot: None, Pivot Bracket: None, Rod End Bracket: W (Double Knuckle Joint)
Magnet: Built-in, Type: Pneumatic, Mounting: Double Clevis, Bore: 20mm, Port Thread: Rc, Stroke: 50mm, Cushion: Rubber Bumper, Rod End Thread: Male Rod End, Rod Boot: None, Pivot Bracket: None, Rod End Bracket: Double Knuckle Joint, Auto Switch: -, Leadwire or Prewired Connector: -, Number: -
CBM2-20-PS-W CBM2-25-PS-W CBM2-32-PS-W CBM2-40-PS-W 11 Lock spring Stainless steel 12 Bumper Urethane * Seal kit includes @6 and @7. Order the seal kit, based on each bore size. (Except #3.) * Seal kit includes a grease pack (10 g). Order with the following part number when only the grease pack is needed.
30o MM W W AL T T A A A MM L H H H 25 Series CA2 Simple Specials These changes are dealt with Simple Specials System.
Contents 32 MBB32-PS-W 40 MBB40-PS 50 MBB50-PS 63 MBB63-PS 80 MBB80-PS 100 MBB100-PS 40 MBB40-PS-W 50 MBB50-PS-W 63 MBB63-PS-W 80 MBB80-PS-W 100 MBB100-PS-W Set of the nos. @9, #0, #1, #2, #3 Set of the nos. @9, #0, #1, #2, #3 * Seal kits consist of items @9 to #3, and can be ordered by using the seal kit number corresponding to each bore size. * Trunnion type should not be disassembled.
CA2-40Z-PS CA2-50Z-PS CA2-63Z-PS CA2-80Z-PS CA2-100Z-PS Rod seal 1 pc Contents Piston seal 1 pc of the Cushion seal 2 pc seal kit Cylinder tube gasket 2 pc Note) Seal kits include grease pack.
MB32ZCA2-40Z CA2-50Z CA2-63Z CA2-80Z CA2-100 Z-PS MB125-PS PS -PS -PS -PS -PS Rod seal 1 pc Contents of Piston seal 1 pc the seal kit Cushion seal 2 pc Cylinder tube gasket 2 pc Note) Seal kits include grease pack.
Mounting D: Double clevis Pivot bracket N: Yes Rod end bracket W: Double knuckle joint Auto switch D-M9BW: 2 pcs.
W W W W W W W W W W W W W W W W W W W W 10, 15 W W W W W Change of the length of standard chamfered face W Change of the length of standard chamfered face Two-sided chamfer Two-sided chamfer Shaft through-hole Shaft through-hole and female thread Shaft through-hole and female thread Shaft through-hole and female thread Shortened shaft Shortened shaft Shortened
W : W max. value is from
8 @5 @3 w !6 !5 !1 !2 !0 Actuators !3 !
12) Stroke: Up to 20 stroke 0.1 0.1 D-X 0.05 0.05 Weight W (kg) Weight W (kg) 0.04 0.04 200.03 0.03 Data 0.02 0.02 8 8 0.01 0.01 0 5 10 15 20 25 30 5 0 10 15 20 25 30 Overhang L (mm) Overhang L (mm) Graph (10) Stroke: Up to 30 stroke Graph (13) Stroke: Up to 30 stroke 0.1 0.1 0.05 0.05 Weight W (kg) Weight W (kg) 0.04 0.04 0.03 0.03 0.02 0.02 8 8 0.01 0.01 0 5 10 15 25 20 30 0 5 10 15 20
When sum of load rate does not exceed 1, it is possible to use. 1+2+3<1 163 Series MXP Precision Air Slide Table How To Order How to Select Allowable load:W(N) Fig. 1 Over hung:Ln(mm), Corrected value for center position distance of moment:An(mm) Fig. 2 Pitch moment Yawing moment Roll moment W L2 A2 L1 A1 L3 A3 Mp Mr My Static moment Kinetic moment W W W L2 A2 L3 A3 L1 A1 W Mp Mr My W W
Can be used based on n = + + '+ + ' = 0.25 + 0.022 + 0.011 + 0.17 + 0.24 = 0.693 1 n = + + + n 1 7 Air Slide Table Series MXQ Load weight: W (kg) Overhang: Ln (mm), Corrected value of moment center position distance: An (mm) Work piece mounting coefficient: K Fig. 3 Fig. 1 Fig. 2 Pitch moment Yaw moment Roll moment Table mounting W W My Mp Mr W W W Static moment Dynamic moment L
9 w %7 $1 $2 $3 $6 $8 $9 $0 #3 #0 @5 #2 $5 $4 %0 %1 t y !2 !1 !3 CL u !4 !6 CL1 !7 !5 MLGC CNG e ^0 ^2 !
(kg) Fig. (2) Overhang: Ln (mm), Correction Values for Moment Center Distance: An (mm) Pitch moment Yaw moment Roll moment W My Mr Mp W W W L3 A5 L1 A1 Adjusting bolt Static moment L2 A3 W MX Mp Mr My MTS W W W MY L1 A2 L3 A5 W L2 A4 CY Mey Note) No need to consider this load factor in the case of using perpendicularly in a vertical position.
As a guide, adjust P2, so that it could be W + P2A = P0a.