Table of Contents

-XC9 Adjustable stroke cylinder/Adjustable retraction type -XC35 With coil scraper Applicable stroke (mm) -XC79 Machining tapped hole, drilled hole, and pin hole additionally. Caution Example Positioning accuracy for pin hole on the plate Dispersion of dimensions when machining each component will be accumulated in the plate pin hole positioning accuracy when mounting this cylinder.

10

V V V V D CM3 V V V V V v v MBl-lJ K v 25A CG1 v v MBlR V CG3 v v v v v v 10v 20JMB v v XAl MB MB v v v v v v v XB5 v v v v v XB6 MB1 v v v v v XB13 CA2 v v XC3 v XC4 CS1 v v v v v XC5 CS2 v XC6 Note 8) Note 8) v XC7 v v v XC8 v v v XC9 v v XC10 Note 4) Note 4) v v v v v XC11 v v v v v XC12 v v XC14 Note 3) v v v v v XC22 XC26 v v XC27 v v v v XC29 XC30 v v XC35

MGG

With Coil Scraper 11 MGG XC35 Standard part number from page 1 With coil scraper Scrapers are used on the piston rod and guide rods (front and rear) to protect the seals by removing frost, welding spatter and chips, etc., that adhere to the moving parts.

MG

-XC6 Piston rod and rod end nut made of stainless steel -XC8 Adjustable stroke cylinder/Adjustable extension type Theoretical Output -XC9 Adjustable stroke cylinder/Adjustable extension type -XC22 Fluoro rubber seals OUT IN -XC35 With coil scraper (N) -XC69 With shock absorber Rod size (mm) Operating direction Piston area (mm2) Operating pressure (MPa) Bore size (mm) -XC79 Machining tapped

Air Cylinder

-XC35 With coil scraper Auto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting Operating range Auto switch mounting brackets/Part no.

MB

Dimensions Bore size (mm) 32 40 50 63 80 100 44 Series MB Made to Order Specifications With Coil Scraper -XC35 Double Clevis Pin and Double Knuckle Pin Made of Stainless Steel -XC27 15 18 Scraper removes frost, weld spatter, cutting dust, and etc., and it protects the seals.

CM2

.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com MB Standard Stroke Maximum stroke (mm) Standard stroke (mm) Note) Bore size (mm) MB1 20 1000 CA2 25 1500 25, 50, 75, 100, 125, 150 200, 250, 300 32 CS1 2000 40 2000 Made to Order Specifications (For details, refer to page 6-17-1.)

MB1

Standard part number MB1 XC35 With coil scraper Specifications Action Cushion Wiper ring Double acting single rod Air cushion, Rubber bumper Coil scraper (metal) Specifications other than the above are the same as the standard type.

CATALOG

Note 4) Grommet type (G) is also available for C-kit, single type of VQ0/1000/2000.

A

32 100, 200, 300, 400, 500, 600, 700, 800, 900, 1000, 1200, 1400, 1600, 1800, 2000 40 100, 200, 300, 400, 500, 600, 700, 800, 900, 1000, 1200, 1400, 1600, 1800, 2000 O P T I O N S T R O K E A D J U S T M E N T U N I T Stroke Adjustment Unit 25 MY-A25L 32 MY-A32L 40 MY-A40L 25 MY-S25L MY-S25B 32 MY-S32L MY-S25B 40 MY-S40L MY-S32B M O R E H O W T O O R D E R S E E N E X T P A G E Courtesy

Title not found

Pul the valve up at the front Tie-rod base manifold (Serbs SV1 000/2000/3000/4000) Conventional tie-rod base type manifolds with 34 pins connector allows up to 16 stations with double solenoids. ( ( Valve Manual Override ffi ffi Manitold block type ' Ava abelon y lor SV1000/2000 .

NCDA1F150-1600-XA22, TIE ROD CYLINDER, 2.42 lb

NCDA1F150-0125-A54L, TIE ROD CYLINDER, 1.15 lb

NCDA1F150-1200-XA22M, TIE ROD CYLINDER, E14, 2.08 lb

NCDA1F150-0100-XA7, TIE ROD CYLINDER

NCDA1F150-0400-XA7, TIE ROD CYLINDER

NCDA1F150-0350-XA7, TIE ROD CYLINDER

NCDA1F150-0500-XA22, TIE ROD CYLINDER

NCDA1F150-1600-XA7, TIE ROD CYLINDER, 2.42 lb

NCDA1F150-1000-XA22, TIE ROD CYLINDER, E14, 1.91 lb