CY1F Operate the piston within a range such that collision damage will not occur at the stroke end. 5. Consider a possible drop in operating pressure due to a power outage, etc. When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc.
Determination of load's kinetic energy (E) bore size E > Es E Es Determination of bore size Review of larger bore size E = m E 2 a ( ) 2 = (Refer to page 8-16-8.) 1000 P Ps P > Ps Determination of pressure for intermediate stop (p) (Refer to page 8-16-8.)
Determination of load's kinetic energy (E) E > Es E Es Determination of bore size Review of larger bore size E = m E 2 a ( ) 2 = (Refer to page 1548.) 1000 P Ps P > Ps Determination of pressure for intermediate stop (p) (Refer to page 1548.)
KW N N Adjustment bolt A Z + Stroke Concentrated piping on left (CY1F10 to 25L--) KA KB EW 2-P Hexagon socket head bolt For adjustment bolt fixing HW ES (Piping port) 2-P (Hexagon socket head plug) EY HA GB EH KC KH H GB GA HB G GA N N KW A Z + Stroke Adjustment bolt GD GC Model Standard stroke EB A EA EH ES EW EY G GA GB GC GD H HA HB HW CY1F10 49 10 16 7 6.5 16 27 9 7 19.5 14 6 28 26 14
when a 63 air cylinder is operated at a maximum drive speed of 500mm/s.
Applicable for a wide range of liquids The element is applicable for a wide range of liquids because it adopts PTFE seals.
ruct i ons are i nt ended t o prevent a hazardous si t uat i on and/or equi pm ent dam age.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Bore size (mm) Series MHS2 Series MHS3 * es MH94 Beler to catalog ES20-104F a a a a a a a a a r a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a MHF2 Very low profile Reduced height saves space minimizes bending moments in pick and place systems The MHF2 Low Profile Air Gripper uses a low profile design to save space and reduce bending moments.
When tightening the auto switch mounting screw, use a watchmakers screw driver with a handle diameter of about 5 to 6mm. Furthermore, use a tightening torque of 0.05 to 0.1 Nm. As a rule, it should be turned about 90 from the point at which tightening can be felt. Use a tightening torque of 1 to 1.2 Nm for the hexagon socket head set screws (M4 x 0.7). 1.
AD17-A AD27-A AD37-A AD47-A Spacer Y100-A Y200-A Y300-A Y400-A Y500-A Y600-A Spacer with bracket Y100T-A Y200T-A Y300T-A Y400T-A Y500T-A Y600T-A Check valve Note 5) Note 6) AKM2000-01-A (02)-A AKM3000-(01)-A 02-A AKM4000-(02)-A 03-A Pressure switch Note 6) IS10M-20-A IS10M-30-A IS10M-40-A IS10M-50-A IS10M-60-A T-spacer Note 5) Note 6) Y110-M5-A Y210-01-A (02)-A Y310-(01)-A 02-A Y410-(02
eJt Alj0to60 Drain cock with barb frtling:06 x 04 nylon tube AL30 to 60 Port size Drspay -a 15 Jor p odJcl dmp pl"_e ano p,es"urF qdJqe DSI "l AL10 to 60 Wfen mo,e lhan one specJcation s reqL red,Indcale n ascend ng nume ca then atphabeLLcaL ode( Nole)For M5 a.d \PTthreaa ypes Accessory a a a a a a a a a a a a a a a a a a a a a a a a a a a a a o a a a a a a a a a a a a a a a a a a o a a
(The switch will stay ON all the time.) 1) For an auto switch without a contact protection circuit, use a contact protection box when the wire length is 5m or longer.
A scraper is not installed. A separate version -X324 (with a felt dust seal) is available in cases in which dust, etc. is dispersed throughout the environment. Mounting taps have been added on the surface opposite the standard positions.
When used without a guide for a light load. (Application Example 1) When space is very limited.
IDX-OM-W011-B / Series IDF1E/2E/3E-10(-A,C,S) IDF3E-20(-A,C) IDF4E-10(-A,C,L,M,R,S,T) IDF4E-20(-A,C,L,M,R,T) IDF6E-10(-A,C,K,L,M,R,S,T) IDF6E-20(-A,C,K,L,M,R,T) IDF8E-10(-A,C,K,L,M,R,S,T) IDF8E-20(-A,C,K,L,M,R,T) IDF11E-10(-A,C,K,L,M,R,S,T) IDF11E-20(-A,C,K,L,M,R,T) IDF15E1-10(-A,C,K,L,M,R,S,T) IDF15E1-20(-A,C,K,L,M,R,T) URLhttps://www.smcworld.com/ English instruction manual can be downloaded
9 i *1 *1 C95K32 A A-A A !2 !1 @4 Component Parts Description Aluminum die-casted Aluminum die-casted Aluminum alloy Stainless steel Aluminum alloy Rolled steel Rolled steel Oil impregnated sintered alloy Steel Steel for spring Carbon Steel Steel Steel Material No. !4 !5 !6 !7 !8 !
From a point indicating 500 mm/s on the axis of abscissas, extend a line upward and find a point where it intersects with a line for the 63 mm bore size. Extend a line from the intersection to the left and find a load mass 80 kg.