1.1 l/min, total lifting height 14/15 m) 24/32 20 0.14/0.19 (at 10/10 l/min, total lifting height 11/16 m) 10/10 10 Rc 1/2 Stainless steel, Brass, PE, PVC, PPE, Copper brazing (Heat exchanger) Stainless steel, PE, PVC, Brass, Copper brazing (Heat exchanger) Wetted parts material 5 to 32 0.2 to 0.5 27/28 Rc 1/2 5 to 32 0.2 to 0.5 12/15 Rc 1/2 5 to 32 0.2 to 0.5 10/12 Rc 1/2 Temperature range
Body Style: M (Body Ported Stacking Manifold Type), Coil Voltage: 5 (24VDC), Flow Rate: D (Power Consumption: 0.5W, Operating Press: 0.5MPa, Cv: 0.011), Electrical Entry: C (Plug Lead w/Light/Surge Suppressor), Port Size: 32 (Body Ported, Barb Fitting ø3.18/ø2), Made to Order: X62 (Normally Open Type)
Specification for Option M 11.3 Installation of motor type auto drain 1) Hold the hexagon-head part (width across flats: 32) at port Rc1/2 of the air dryer with spanner. Then install nipple, ball valve (width across flats: 25). Note 1) Put up the seal tape or the sealant to the nipple. Torque R1/2: 28 to 30Nm 2) Hold the ball valve with the spanner.
During operation: 36 to 113 oF (2 to 45oC) During storage: 32 to 122oF (0 to 50oC) (when there is no drain water inside of the piping) Avoid locations where temperature substantially changes. Avoid locations where strong magnetic noise occurs. (Avoid locations where strong electric field, strong magnetic fields, or surge voltage occur).
Supply the power to the extent so that such voltage sag will not happen. ERR11 (2) Voltage sag happens. (1) Check the set value for high temp. cutoff temperature and confirm the temperature really reaches abnormal value. (1) Internal temp. sensor value exceeds the high temp. cutoff temperature.
Ensure that voltage sag does not happen. (4) Voltage sag happens. (1) Check the set value for high temp. cutoff temperature and confirm the temperature really reaches this value. (1) Internal temp. sensor value exceeds the high temp. cutoff temperature. (2) Flow rate of circulating fluid is zero.
Ensure that voltage sag does not happen. (2) Voltage sag happens. (1) Check the set value for high temp. cutoff and confirm the temperature reaches this value. ERR12 (1) Internal temp. sensor value exceeds the high temp. cutoff temperature. (2) If the flow rate of the recirculating fluid is zero, the temperature of recirculating fluid cant be detected and might increase.
If the product is subjected to a short power outage (including voltage sag), it may take a long time to resume normal operation or be unable to restart normally due to the protective equipment triggered after the power is recovered. In this case, turn off the switch of the product and reset the protection circuit referring to 6.2 Reset the Thermal relay and High Pressure Switch.
If the product is subjected to a short power outage (including voltage sag), it may take a long time to start operating normally or be unable to restart normally due to the protective equipment triggered after the power is recovered. In that case, turn off the switch with lamp on the body once, and reset the protective equipment circuit referring to 5.2 Reset of protective equipment.
Body Style: Body Ported Stacking Manifold Type, Coil Voltage: 5 VDC, Flow Rate: Power Consumption: 0.35W, Operating Press: 0.1MPa, Cv: 0.016, Electrical Entry: Grommet, Port Size: Body Ported, Barb Fitting ø3.18/ø2, Made to Order: -, Lead Wire Length: -
Body Style: M (Body Ported Stacking Manifold Type), Coil Voltage: S (5 VDC), Flow Rate: A (Power Consumption: 0.35W, Operating Press: 0.1MPa, Cv: 0.016), Electrical Entry: G (Grommet), Port Size: 32 (Body Ported, Barb Fitting ø3.18/ø2)
If the product is subjected to a short power outage (including voltage sag), it may take a long time to start operating normally or be unable to restart normally due to the protective equipment triggered after the power is recovered. In that case, turn off the switch with lamp on the body once, and reset the protective equipment circuit referring to 5.2 Reset of protective equipment.
If the product is subjected to a short power outage (including voltage sag), it may take a long time to start operating normally or be unable to restart normally due to the protective equipment triggered after the power is recovered. In that case, turn off the switch with lamp on the body once, and reset the protective equipment circuit referring to 5.2 Reset of protective equipment.
MOUNTING SCREW 1 PIECE, S070C
Body Style: Body Ported, Coil Voltage: 5 VDC, Flow Rate: Power Consumption: 0.5W, Operating Press: 0.3MPa, Cv: 0.016, Electrical Entry: Plug Lead w/Light/Surge Suppressor, Port Size: Body Ported, Barb Fitting ø3.18/ø2, Made to Order: -, Lead Wire Length: -
Body Style: Body Ported, Coil Voltage: 6 VDC, Flow Rate: Power Consumption: 0.35W, Operating Press: 0.3MPa, Cv: 0.011, Electrical Entry: Plug Lead w/Light/Surge Suppressor, Port Size: Body Ported, Barb Fitting ø3.18/ø2, Made to Order: -, Lead Wire Length: -
Body Style: Body Ported, Coil Voltage: 6 VDC, Flow Rate: Power Consumption: 0.5W, Operating Press: 0.3MPa, Cv: 0.016, Electrical Entry: Plug Lead w/Light/Surge Suppressor, Port Size: Body Ported, Barb Fitting ø3.18/ø2, Made to Order: -, Lead Wire Length: -
Body Style: Body Ported, Coil Voltage: 6 VDC, Flow Rate: Power Consumption: 0.5W, Operating Press: 0.5MPa, Cv: 0.011, Electrical Entry: Plug Lead w/Light/Surge Suppressor, Port Size: Body Ported, Barb Fitting ø3.18/ø2, Made to Order: -, Lead Wire Length: -
Body Style: Body Ported, Coil Voltage: 3 VDC, Flow Rate: Power Consumption: 0.5W, Operating Press: 0.3MPa, Cv: 0.016, Electrical Entry: Grommet, Port Size: Body Ported, Barb Fitting ø3.18/ø2, Made to Order: -, Lead Wire Length: -
Body Style: Body Ported, Coil Voltage: 12 VDC, Flow Rate: Power Consumption: 0.35W, Operating Press: 0.3MPa, Cv: 0.011, Electrical Entry: Plug Lead w/Light/Surge Suppressor without connector, Port Size: Body Ported, Barb Fitting ø3.18/ø2, Made to Order: -, Lead Wire Length: -