Compact Hydraulic Cylinder Double Acting/Double Rod Series CH QWB ø 20, ø 32, ø 40, ø 50, ø 63, ø 80, ø 100 Since Series CHQWB does not have an air release plug, release air from components other than the cylinder (e.g. from piping, etc.) as well. 6. When mounting the cylinder body with mounting bolts, use tightening torques in the table below as a guide. 1. Use hexagon socket head cap screws (JISB1176, strength class 10.9 or higher) for cylinder mounting. (20: 2pcs, 32 to 100: 4pcs.) 2.
For the Originator Device, select an arbitrary [Input Tag Set] and [Output Tag Set], with the same number of bytes as the [Output Tag Set] and [Input Tag Set] in the Target Device, and register the Input/Output connection.
(Page 20) Communications RS-232C/RS-485 Weight Approx. 20 kg Approx. 21 kg Accessories Power supply connector, Operation Manual Power supply cable should be ordered as an option (sold separately, page 22) or prepared by the user.
When in the locked state, do not apply a load accompanied by an impact shock, strong vibration or turning force, etc. Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 2. Consider stopping accuracy and the amount of over-run when an intermediate stop is performed.
When in the locked state, do not apply a load accompanied by an impact shock, strong vibration or turning force, etc. Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 2. Consider stopping accuracy and the amount of over-run when an intermediate stop is performed.
Beware that earth leakage from the equipment around the switch such as pump and stray current caused by ground fault should not flow into the fluid to be measured. 1. Take precautions when using the switch for an inter lock circuit.
reference value Based on the saved reference value, output on-off points controlled by set values2 such as , , , and will also be rectified. 2 When an output is reversed, output on-off points displayed at , , , and will be rectified.
An application which has the possibility of having negative effects on people, property, or animals, requiring special safety analysis. d. When used in an interlock circuit, dual interlock such as mechanical protection is necessary in case of accident. Periodical inspection is also necessary to confirm proper operation.
Valve specifications Note 1) Conductance is molecular flow measured with an elbow pipe which has the same dimension as each applicable flange. Note 2) For one cycle of cylinder.
Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 2. Consider stopping accuracy and the amount of overrun when an intermediate stop is performed. Due to the nature of a mechanical lock, there is a momentary lag with respect to the stop signal, and a time delay occurs before stopping.
When mounting with bracket mounting nuts, tighten them using the tightening torques in the table below as a guide.
Conduct stroke adjustment with an adjustment bolt as follows: The adjustment bolt should be secured on the same surface as the shock absorber after stroke adjustment. If the stopper surface of the shock absorber and the end surface of the adjustment bolt are not on the same level, it may result in an unstable stop position of the slide table or reduced durability. 5.
Install an air filter. Install an air filter at the upstream side of valve. Select an air filter with a filtration degree of 5 m or finer. 8. Interference in oval type release button The following models cannot be used if a box wrench or socket wrench is used. 2. Install an aftercooler, air dryer or water separator, etc.
Never use in an atmosphere of explosive gases. The switches do not have an explosion proof rating. Never use in the pressure of an explosive gas as this may cause a serious explosion. Maintenance Warning Mounting 1. Perform a periodical inspections for proper operation of the switch. Unexpected malfunction or erroneous operation may lead to failure in ensuring safety. 2.
Description Lead wire color Note 1 DC(+) Brown 12 to 24 VDC Blue (30.8) 2 OUT2 White Switch output 2 24.55 Black 3 DC() Blue 0 V 4 OUT1 Black Switch output 1 When used as an IO-Link device 15 No.
Keep wiring as short as possible to prevent interference from electromagnetic noise and surge voltage. Do not use a lead wire longer than 30 m. Wire the DC (-) line (blue) as close as possible to the power supply. Operating environment Do not use the product in an environment where the product is constantly exposed to water or oil splashes. Otherwise it can cause failure or malfunction.
D-X Technical Data 1359 MY1W Series Auto Switch Mounting 2 Note) Since the operating range is provided as a guideline including hysteresis, it cannot be guaranteed. (Assuming approximately 30% dispersion.) It may vary substantially depending on an ambient environment.
Equipped with an auto switch (Mountable on both sides) Magnet included as standard. Reed switch: D-A7/A8 Solid state switch: D-F7/J7 ( ) Series MRQ An air cushion is also available.
Unpacking the sealed package Since the filter and element are sealed in an antistatic double bag, the inner package should be unpacked in a clean atmosphere (such as a clean room). 316