Brake mechanism added Applicable bore size Dd9 L1 L2 m d Drill through Included split pin Included flat washer Clevis Knuckle 2 x d Dd9 CDP-2A 40 10 0.040 0.076 46 38 4 3 3 x 18 L Polished round 10 L1 L2 m L1 L2 m CDP-3A 50 40, 50, 63 12 0.050 0.093 55.5 47.5 4 3 3 x 18 L Polished round 12 2 x d Dd9 CDP-4A 63 16 0.050 0.093 71 61 5 4 4 x 25 L Polished round 16 L1 L2 m CDP-5A 80 18 0.050 0.093 76.5 66.5 5 4
= 50 [mm] D-X L2 L1 20Data Item Load factor n Note 1.
Collision speed V (mm/s) Note) Use the average speed when calculating static moment.
[Change to the next mode] To change to the next mode and store the selected CH setting press the S button once, the and S button simultaneously for 2 s or longer, or the S button for 3 s or longer. (for the IZTC40, the mode does not change by pressing button and S button for 2 s or longer.)
N Rubber bumper 100 CG1 25 B S Z N CDG1 With auto switch M9BW 100 B 25 N S Z With auto switch (Built-in magnet) Number of auto switches Rod end thread Mounting Nil Male rod end F Female rod end Nil 2 pcs. S 1 pc. n n pcs.
Dynamic moment MG Va Calculation Example CX m Operating Conditions Cylinder: CYV32 Mounting: Horizontal wall mounting Maximum speed: U = 300 [mm/s] Load mass: m = 1 [kg] (excluding mass of the arm section) L1 = 50 [mm] L2 = 50 [mm] D-X L2 L1 20Data Item Load factor n Note 1. Maximum load mass m 1 = m/m max = 1/5 = 0.20 L2 Review m. L1 2.
] L2 = 50 [mm] D-X L2 L1 20Data Item Load factor n Note 1.
200mm/s 30mm/s 80mm/s Positioning repeatability :tO.05mm i0.03mm Type ot guide Linear guide Operating temperature range s to 4o"C (40-105"F) Pitch (Nm) Statlc moment allowance Boll (Nm) Yaw (Nm) 4 Construction Com 1 0 Stopper B Sensor plate Sofl steel Chrcmated 12 Co!
Horizontal collision Vertical (Downward) Vertical (Upward) MY3A MY3B m s MY3M Type of impact m s Caution s m
200mm/s 30mm/s 80mm/s Positioning repeatability :tO.05mm i0.03mm Type ot guide Linear guide Operating temperature range s to 4o"C (40-105"F) Pitch (Nm) Statlc moment allowance Boll (Nm) Yaw (Nm) 4 Construction Com 1 0 Stopper B Sensor plate Sofl steel Chrcmated 12 Co!
EX510-VSS EX510-VSQ L 20 20 L 20 20 2.8 2.8 B C A How to Order EX510-V + 10 S S EX510-VWS EX510-VWQ Output Valve connector L 20 20 L 20 20 S W 1 point 2 points Nil S Q None For SY, SYJ series For VQ, VQZ series Note) Cable length (L) 2.8 2.8 10 30 1 m 3 m B C A + Note) VQ is compatible with the positive common only.
Piston speed mm/s Piston speed mm/s Select the load mass from within the range of limits shown in the graphs.
41 Type VV5K3-(S)42 Manifold base Applicable base: In common for all types of VV5K3 models Mounting Screw Tightening Torques Mounting Screw Tightening Torques Caution Base mounted Caution Body ported VK3000-6-1A Manifold gasket Screw assembly VK3000-6-2A M3: 0.6 Nm M3: 0.6 Nm Note) Mounting direction is not flexible.
S Coil Diode Coil Diode Use caution in wiring because it will not meet the IP65 (enclosure) standard if you use the other cable than prescribed heavy-duty cable of size (3.5 to 7). Tighten the ground nut and set screw within the specified range of torque.
T[s] = (V/10) X (T2 T1)/(Z) T(s) = (4.8/10) X (12 3.7) = 4 NO NO Increase number of booster regulators (Z) to decrease T.
, Hyteresis Repeatability With 50% of signal input 1 0.8 1 Output deviation factor (% F .S.)
AS 0 0.1 0.15 0.2 0.25 0.3 Return stroke pressure (MPa) ASP ASN v v w w a a o o l l v v l l F F e e AQ ASV u u r r e e s s v v s s a a e e l l v v r r P P e e AK ASS ASR ASF Working stroke Working stroke Return stroke Return stroke Pressure valve Flow valve 15-16-1 2 Cuts air consumption by operating the return stroke at a reduced pressure.
(mm) Model Bracket mounting dimensions Weight (g) S Bracket assembly no.