Sine Rodless Cylinder Series REA The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or return from an intermediate stop using an external stopper, etc. The load should be guided by a ball type bearing (LM guide, etc.). If a slide bearing is used, sliding resistance increases due to the load weight and load moment, which can cause malfunction.
Method (Operation example with an energy saving driver circuit) 2.
.' 80 46 .5 55 46.5 52.5 ; 100 55 62 55 59.5 Reed Type With Conduit Auto Switch Mounting Position And Height (mm) ~ Bore Size Il-A44 J (mm) A B H.
I Compact Guide Cylinder with One-way Lock Series MLGP 40, 50, 63 Prevents dropping when air supply pressure falls or residual pressure is exhausted Can be locked at any position The locking position can be changed to accommodate an external stopper position or the thickness of clamped work pieces, etc.
To install/remove the product, use an appropriate wrench to tighten/loosen at the supplied nut on body B. 12. Mounting Do not apply torque at other points as the product may be damaged. Rotate body A manually for positioning after installation. Warning 1.
arm length of 200 mm and an operating pressure of 0.5 MPa, according to the graph, the maximum clamping force is 2000 N.
Format error 39 An error is found in the attached value of a command being programmed. Refer to the Series LC1 instruction manual for alarm details.
Displacement may increase after an impact load has been applied. When the table is subjected to an impact load, there may be permanent distortion of the guide unit and increased displacement.
When the product is used for an actuator operating vertically, the actuator may lurch depending on the load. For the adjustment method, please refer to Selection and Adjustment on page 15-16-6 to 15-16-7. 4. For installation and removal, tighten the body B by applying an appropriate wrench to the two opposite sides of the hexagon. Using other parts may destroy the valve.
Refer to p.0-39 to 0-46 for Safety Instructions and common precautions. MX MXU Precautions on Handling Warning Mounting/Adjustment Caution MXS MXQ q Do not scratch or gouge the sliding portion of the guide rod by striking it with an object or getting an object trapped in it.
Please contact P/A if hysteresis causes an operational problem. 15 Auto Switch Connections and Examples Basic Wiring 2-wire Solid state 3-wire, NPN (Solid state) 2-wire Solid state 3-wire, PNP (Reed switch) Brown Brown Brown Brown Load Load Indicator light Protective circuit etc.
Our pressure switches do not have an explosion proof rating. Never use in the presence of an explosive gas as this may cause a serious explosion. 1. Do not drop, bump, or apply excessive impacts (980 m/s2) while handling. Although the body of the sensor may not be damaged, the internal parts of the sensor could be damaged and lead to a malfunction. 2.
The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved. 3. When air is supplied for the piston extension, the check seal opens and the piston extends with no delay.
The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved. 3. When air is supplied for the piston extension, the check seal opens and the piston extends with no delay.
M1 M2 M3 m1 m2 m3 16 25 40 16 25 40 16 25 40 5 4 3.5 18 16 14 MY2H 13 14 10 35 35 30 45 33 28 68 66 57 7 6 7 15 13 13 MY2H 28 26 26 32 30 30 60 50 60 62 62 62 46 55 46 20 18 18 MY2HT 100 120 100 38 35 35 200 220 200 80 80 80 The above values are the maximum allowable values for moment and load.
When the work holding point is out of range, the unbalanced load applied to the finger and the guide section may cause excessive play in fingers and have an adverse effect on the gripper life.
size Stroke symbol MHL2 MHT2 The packing class has been revised to adopt oil-proof materials for using it in an environment with splashing of cut liquid splashing etc.
If foreign matter is adhering to the parts, perform an appropriate procedure, such as blowing with air or cleaning with neutral detergent. Closing the valve: Turn 90 counterclockwise from the open state to the original state to close the valve. Perform an eletrical operation at the position where the valve is closed.
The standard arrangement of manifolds should be placed on an individual port on this side, each solenoid valve from the left side and a blank plate in the right side. The right side of the common port provides plug. 17-3-99 4 The VX series will be revised shortly.
Cannot be used as an emergency shutoff valve, etc. The valves presented in this catalog are not designed for safety applications such as an emergency shutoff valve. If the valves are used in this type of system, other reliable safety assurance measures should also be adopted. 2.