MRHQ Gripper Rotation Range/View from Gripper Side 90 The figure at the right indicates the position of the gripper when pressure is applied to port B. 180 When pressure is applied to port A, the gripper rotates clockwise.
Maximum piston speed: 500mm/s Able to operate at 50 to 500mm/s, if within the allowable kinetic energy range. MGG Characteristics MGC MGF Air cushion provided as standard equipment Enables the impact to be absorbed at the stroke end when the cylinder is operated at high speeds.
Model LC1-1-RD Dedicated communication cable (IBM PC/AT compatible computer) Cable length 022m 044m 033m 055m Model LC1-1-RC Cable length 022m 044m 033m 055m PC Controller Controller PC Cable length: 2 to 5m Cable length: 2 to 5m 85
<-III o ~ \ ~ r c-~~ ~ d" -, Rod end without L --' thread r~ \ A~OSW'tCh MM 8 NN LZ --' l S (Across H at) .. s .I w J 2051 3Gst 1561 I (mm) ,5 st lost ~ 1551 sst l. l0S" 20" 1.30>1. P .
1/8 12(PA) port NO 2A VFRA 42 52 NC 12 12 VPA4 3R 1P NC SYJA (1/8) 12(PA) port 12.6 13.5 83 23 VZA 91 VTA VGA 74.5 73.5 VPA VPA 28.5 X VPA3 M5 x 0.8 (Breathing hole) 13.5 28.5 57 1/4, 3/8 1(P) port For vacuum/VPA544V-102 03 A B 1/4, 3/8 2(A) port 13.5 28.5 51 2 x 5.2 (For mounting) 47 23 1/4, 3/8 3(R) port 17.6 NO 2A 42 52 NC 12 3R 1P NC 1/8 12(PA) port 13.5 12.6 91 23 74.5 73.5 28.5 X M5
Example) In the case of 0.3 MPa, Port 2 is a vacuum (1 Torr or less), while Port 1 can be pressurized to 0.2 MPa(G). *2 The reverse pressure potential indicates the pressure which can be applied from Port 2 when Port 1 is at atmospheric pressure. *3 Face seal fitting/compression fitting only *4 Leakage when the ambient temperature is at 20C and there is 0.1 MPa of differential pressure.
Information End Lock Cylinder Series CBG1/20, 25, 32, 40, 50, 63, 80, 100 Door locking Drop prevention at end of lift With rear lock With front lock Lock Open Close Lock Holds a cylinder position even with the air supply off Prevents trouble at the restart of operation by locking when the air is exhausted at the stroke end position.
L plug connector (L): SYJ34-L-M5 M plug connector (M): SYJ34-M-M5 M8 connector (W0): SYJ34-W0-M5 Approx. 300 (Lead wire length) 41.5 [48.5] 26.1 46 M8 x 1 28.5 52.6 [59.6] Approx. 300 (Lead wire length) 58.5 [60.7] 48.7 [50.9] 57.6 50.2 43.7 R P R P R P 10 8.6 10 8.6 10 8.6 23 23 23 5 5 5 28.5 28.5 28.5 35.6 35.6 35.6 Refer to the page 68 for dimensions with connector cable. 6 Series SYJ300
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com ZSP ISA2 IS ZSM PF2 IF For details about certified products conforming to international standards, visit us at www.smcworld.com. Data Push-button calibration allows for precise and simple set up.
Adjust the cushion needle so that sufficient kinetic energy will be absorbed during a cushion stroke and no excessive kinetic energy will remain when the piston collides at the stroke end.
Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature.
Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Note 5) In vaccum applications, use 10Clean Series which can use with 3 (R) port vacuum and 1 (P) port vaccum release pressure.
O-ring seal Fine adjustments at the end of the stroke Fine adjustments between 2 to 0mm can be made on one side (4 to 0mm for both sides).
When using a cylinder at around the lower limit of the operating range, it is recommended to use a cylinder with lock mechanism. Additionally, be aware that the transferred object may be pushed back due to the return force of the shock absorber. MIW MIS 40 30 20 3.
9 Wear ring CM-020-07-301A CM-025-07-302A CM-032-07-304A C1A040-07-305A Resin @0 Piston gasket SO-012-13 SO-010-22 SO-010-23 SO-013-7 NBR @1 Cylinder tube gasket CM-020-16-123 CM-025-16-124 CM-032-16-126 CM-040-16-127 NBR @2 Rod seal PDU-10Z PDU-12LZ PDU-12LZ PDU-16Z NBR @3 O ring SO-017-30 SO-017-32 SO-017-34 SO-017-36 NBR @4 O ring SO-015-23 SO-015-23 SO-017-36 SO-017-37 NBR @5 4.10-10
HI , 32 7 0 43 78 t 40 '8 0 43 82.5 SO 8 0 43 87.5 63 23 0 43 94 80 13 0 43 103 100 23 0 43 11 3.5 0syC 19 Series C95 MounUng AccesSOt'ies Part number rri~~ Pescriptlot) , . _,C9S1132 C95ia40 /, C95850 C951163 / C9511180 C951l1100 Tmnniol'lIncuitilgbl'acllet Nae'l MB-S03 MB-S04 MB-S06 MB-S10 fMoo.m; pI!
at rod end indicates the value in rod end female thread.
F Full duplex Communication system that can send and receive data at the same time bidirectionally (similar to standard telephone). H Half duplex Communication system that sends and receives data in one direction at a time (similar to two-way radio). A 32 bit digit sequence which is assigned to identify devices which are connected to the network.
The lightweight stainless bowl with reduced thickness allows for easier element replacement. 1 2 3 At least 30 mm of maintenance space is necessary for removing the bowl. Loosen the 4 securing bolts. Rotate the bowl to release the stopper. Pull it down to remove the bowl.
at rod end indicates the value in rod end female thread.