Liquid dripping: 0.02 to 0.77 cm3 at each removal Aeration: 0.1 to 2.7 cm3 at each removal DM KDM KB Socket valve Plug valve KR KA KQG2 KG KFG2 MS KKA KKA KP LQ MQR T Non-greased specification (standard) Allows smooth installation and removal even without grease O-ring: Fluorine coated Sliding parts of plug and socket: Fluorine coated is used.
Furthermore, when pipe tape is used, leave 1.5 to 2 thread ridges exposed at the end of the threads.
Dynamic moment Va Calculation Example m Operating conditions Cylinder: CYV32 Mounting: Horizontal wall mounting Maximum speed: U = 300 [mm/s] Load mass: m = 1 [kg] (excluding mass of the arm section) L1 = 50 [mm] L2 = 50 [mm] L2 L1 Item Load factor n Note 1. Maximum load mass m 1 = m/m max = 1/5 = 0.20 L2 Review m. L1 2.
Refer to the figure at right. Bowl Assembly The remainder depressure cock. It opens when turning in the direction of the arrow of figure.
Table yaw deflection due to static yaw moment applied at arrow for fully extended stroke of slide table. Table yaw deflection due to static yaw moment applied at arrow for fully extended stroke of slide table.
To install/remove the product, use an appropriate wrench to tighten/loosen at the supplied nut on body B. 12. Mounting Do not apply torque at other points as the product may be damaged. Rotate body A manually for positioning after installation. Warning 1.
For the maximum allowable load mass for each piston speed, please refer to Graph (1). 1600 26 25 23.5 The above value represents the applicable load at the position where the moment does not work at the time of stop. Factors such as impact, etc. are not in consideration with the value.
Table displacement when loads are applied to the section marked with the arrow at the full stroke. Table displacement when loads are applied to the section marked with the arrow at the full stroke.
VQZ Plug Lead Unit U Type (Large Flow Capacity) Mounted Manifold (VV3Q12U) VZ L1 L2 7 4-PT1/8 VS P, E port 7 16 P E P E 29 14 7 32 40.1 49.8 300 Round head screw M1.7 X 14 2-3.5 Mounting hole Manual override 15.5 P=10 300 n 5 4 3 2 1 U side D side 46.5 35.2 19.4 15.5 A A 9.5 16.7 P=10 n-M5 A port Dimensions Equation: L1=10n+21 L2=10n+7 n: Station (Max. 20 stations) n L L1 L2 1 31 17
(coil temperature 20C, at rated voltage, without surge voltage suppressor) When equipped with DC solenoid/surge voltage suppressor, a delay of about 20 to 30msec occurs in the OFF response time.
Do not short-circuit these terminals. [1] Main circuit power input terminals, L1, L2 and Control power input terminals, L1, L2: Connect the 200VAC external power supply to the power supply. Refer to the power supply specification for the size of the acceptable electric wire. [2] Connect the motor cable (U, V, W) to the servomotor connection terminals (U, V, W).
Dynamic moment MG Va Calculation Example CX m Operating Conditions Cylinder: CYV32 Mounting: Horizontal wall mounting Maximum speed: U = 300 [mm/s] Load mass: m = 1 [kg] (excluding mass of the arm section) L1 = 50 [mm] L2 = 50 [mm] D-X L2 L1 20Data Item Load factor n Note 1. Maximum load mass m 1 = m/m max = 1/5 = 0.20 L2 Review m. L1 2.
(Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed at both energized energized states in the axial direction and at the right angles to the main valve and armature.
= 50 [mm] D-X L2 L1 20Data Item Load factor n Note 1.
Output 1 Output 2 A B C Dimensions D3 D2 L5 M2 IN L3 L2 L4 OUT IN D1 M1 M1 Applicable tube dia. d L1 Metric Size Weight (g) Model d D1 D2 L3 L2 D3 L1 L4 L5 M1 M2 VR1211F-23 3.2 11.4 8.4 52 6.2 25.7 36.1 17.5 12.7 12.9 26.4 14.8 VR1211F-04 4 12.8 10.4 56 26.6 38.5 21.9 15.7 15.8 30.4 6.8 VR1211F-06 6 12.8 12.8 53.2 28.8 41.9 25.2 16.8 16.8 25.0 Inch Size Weight (g) Model d D1 D2 L3 L2 D3 L1
Note 4) Vibration resistance No malfunction when tested with one sweep of 5 to 200Hz in the axial direction and at a right angle to the armature, in both energized and de-energized states. Impact resistance .. No malfunction when tested with a drop tester in the axial direction and at a right angle to the armature, one time each in energized and de-energized states.
L2 [mm] L2 [mm] L2 [mm] L2 [mm] 600 600 600 600 Y 400 400 400 400 Mer m 200 200 200 200 0 0 0 0 0 10 20 30 40 50 0 10 20 30 40 50 60 0 2 4 6 8 10 12 14 16 0 4 8 12 16 20 24 Work load [kg] Work load [kg] Work load [kg] Work load [kg] 2000 2000 2000 2000 Mep 1500 1500 1500 1500 L3 [mm] L3 [mm] L3 [mm] L3 [mm] m 1000 1000 1000 1000 L3 Z 500 500 500 500 0 0 0 0 0 10 20 30 40 50 0 2 4 6 8 10
Table Deflection (Reference Values) Table deflection due to pitch moment load Displacement at A when load is applied F Table deflection due to yaw moment load Displacement at A when load is applied F Table deflection due to roll moment load Displacement at A when load is applied F A A F A F F L L L L dimension mm L dimension mm L dimension mm MXY6 MXY6 MXY6 100 100 100 MXY8 MXY8 MXY8 100
(Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed at both energized energized states in the axial direction and at the right angles to the main valve and armature.