LX Note 2) Since vibration may increase with low speed operation, use 12mm/s or more as a guide for speed. LC6C-220AD (Refer to page 309 for details.)
Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3.
This may cause secondary damage to the output circuit, external peripheral device, or valve, and may also cause a fire.
thal the cycle starts with a new group; the end-of-cycle may be in the middle of a group.
Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3.
These may be penetrated by fluids, and the penetrating fluids may affect parts of other materials. Table symbols : Can be used. : Cannot be used. : Can be used under certain conditions. Please consult us.
Even though an auto switch operates normally, the load may not operate. Load In the same way, when operating under a specified voltage, although an auto switch may operate normally, the load may not operate. Therefore, the formula below should be satisfied after confirming the minimum operating voltage of the load.
Even though an auto switch operates normally, the load may not operate. Load -9- In the same way, when operating under a specified voltage, although an auto switch may operate normally, the load may not operate.
It may cause damage to the controller or the actuator. 5. Be careful not to be caught or hit by the workpiece while the actuator is moving. It may cause an injury. 6. Do not connect the power supply or power on the product before confirming the area where the work moves is safe. The movement of the work may cause accident. 7.
It may cause damage to the controller or the actuator. 5. Be careful not to be caught or hit by the workpiece while the actuator is moving. It may cause an injury. 6. Do not connect the power supply or power on the product before confirming the area where the work moves is safe. The movement of the work may cause accident. 7.
It may cause damage to the controller or the actuator. 5. Be careful not to be caught or hit by the workpiece while the actuator is moving. It may cause an injury. 6. Do not connect the power supply or power on the product before confirming the area where the work moves is safe. The movement of the work may cause accident. 7.
It may cause damage to the controller or the actuator. 5. Be careful not to be caught or hit by the workpiece while the actuator is moving. It may cause an injury. 6. Do not connect the power supply or power on the product before confirming the area where the work moves is safe. The movement of the work may cause accident. 7.
Your body may then touch the equipment around you, causing injury.
If tightened too much, thread portion may be damaged and gasket may be deformed. This will cause air leakage. On the contrary, if tightening is not sufficient, thread may loosen causing air leakage. qCut the tube perpendicularly to the tube axis to a little longer length than required length.
This may cause secondary damage to the output circuit, external peripheral device, or valve, and may also cause a fire.
Fire, malfunction, or damage to the product may result. Check the specifications before use. Do not use in an environment where flammable, explosive or corrosive gases are present. Otherwise, fire, explosion or corrosion may occur. The product is not designed to be explosion proof. Do not use the product with flammable fluid Fire or an explosion may result.
Fire, malfunction, or damage to the product may result. Check the specifications before use. Do not use in an environment where flammable, explosive or corrosive gases are present. Otherwise, fire, explosion or corrosion may occur. The product is not designed to be explosion proof. Do not use the product with flammable fluid Fire or an explosion may result.
The product may be damaged if excessive force is applied by stepping or climbing onto it. If the fluid may contain foreign matter, install and connect a filter or mist separator to the inlet. The adherence of foreign matter to the vortex generator or detector can cause errors in measurement accuracy. A filter of approx. 40 mesh is recommended.
If the pump is operated for a long time without any fluid inside or in a gas-fluid mixed state, the diaphragm may be damaged or the life may be shortened. Do not continue idling for 3 minutes or longer. 10.
If the pump is operated for a long time without any fluid inside or in a gas-fluid mixed state, the diaphragm may be damaged or the life may be shortened. Do not continue idling for 3 minutes or longer. 10.